79096214403 Kenmore Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
burners 1 would not do anything burned out 2 when from normal to out of control heat would not keep a constance heat
turned off breaker 3 Phil screws open door and on inside range top I would reconmend a board to hold top up square tip for cross bar and pliers to pull wires off fit perfect works really nice
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from TULSA, OK
- Parts Used:
- 316203301
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Broiler element fried, found nothing in town, Part Select delivered in three days
Pulled oven out, took the screws out of back plate cover plate with socket wrench, pulled connectors out through the back, removed the door, pushed the element rods through the two holes, connected the two wires, screwed the element in, put the hangars on for the element, put the back plate on and turned the broiler on, worked great, put the range door back on and has been working great. Great company, hope not to use them again, but good to know they are there with my part.
Gary H.
Gary H.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Phin from HARRISBURG, PA
- Parts Used:
- 316555800
- Difficulty Level:
- Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
The part I ordered has 5 connections and the part to be replaced has 7 connections. I had to ask a friend who is expert in electrical wiring to help.
My friend used a tester to determine where each wire was supposed to connect to. I'm not sure what he did with the extra connections.
Bottom line is this part should work but you need an expert to do it for you because it's, like I said, not exactly like the one to be replaced.
Bottom line is this part should work but you need an expert to do it for you because it's, like I said, not exactly like the one to be replaced.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeff from BELLEVUE, WA
- Parts Used:
- 316555800
- Difficulty Level:
- Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Pliers, Screw drivers
Element burned out
The original instructions were to replace burner and plug wires back in the same plug they came from.
The problem is that the plug order had changed between parts.
Use a pencil to highligt the plug numbers on both new and old plugset, to fint the new plug positions. And need to reorient one of the burners to allow existing wires to reach.
The problem is that the plug order had changed between parts.
Use a pencil to highligt the plug numbers on both new and old plugset, to fint the new plug positions. And need to reorient one of the burners to allow existing wires to reach.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rhonda from PACHECO, CA
- Parts Used:
- 316404002
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
wrong part received and returned
I wanted the bracket for the oven heating element and received the bracket for the broiler.... part returned and now I am stumped about what my next move will be
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Everett from Colchester, CT
- Parts Used:
- 318178110
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Element would not heat up
Removed 2 screws located underneath the front lip of the range top. Lifted range top and supported. Removed the 2 screws at either end of the support bracket. This bracket holds the elements in position. Be careful not to let the elements fall out when removing. The elements are now free to replace. Swap out the old with the new and be sure to reconnect the wires to the correct terminals on the new element. I did 1 wire at a time so as to not make a mistake at reconnecting the wires. Then replace the support bracket with the 2 screws and lower the range top in place and put back the 2 screws that hold the range top in position. VOILA!! Success. It works. The wife is now happy again:)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Denise from Landover, MD
- Parts Used:
- 316538904
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
light bilb went out
replaced it
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- santa from glassboro, NJ
- Parts Used:
- 316490001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
temp was not reading right
remove back panel took out old part splice wire replaced
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Amy from Corona, CA
- Parts Used:
- 5304524341
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Lens cover for oven light broke.
Really a no brainer, but I do have to say that PartSelect customer service is excellent. My part was located and on it's way within a day and arrived a couple of days later.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Abe from Manson, WA
- Parts Used:
- 5304528972
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Burner quit working
Received the new part FAST. Ordered online. Easy to plug in the new part. Will use PartSelect.com again when needed to order parts!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sharon from Foley, AL
- Parts Used:
- 5304524341, 316538904
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken globe in oven and burnt out light bulb
Easy as 1-2-3
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kelly from Marietta, GA
- Parts Used:
- 316135401
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Largest burner was not operational
After turning off the power to the unit, we took it out of the countertop and unscrewed the base of the unit. We then unplugged the damaged coil and plugged in the replacement part. We then screwed the base of the unit back on and replaced the unit in the countertop. The largest burner now works.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Orange, TX
- Parts Used:
- 316135401
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
broke element.
Easy to put in but i droped a screw to hold the element. had to pull another screw to fix it
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David C from Huntington Beach, CA
- Parts Used:
- 316490001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
Temperature not correct.
Pull out stove. Unplug power. Remove four screws on each corner and loosen one screw in the middle. Remove back panel. Locate and unplug sensor connector. Remove one screw from sensor plate. Turn the sensor 45 degrees and pull sensor out from the rear. Connector received had the incorrect plug and terminals so it was necessaary to splice the connector from the one removed to the one received. Cut and splice wires as necessary. Install sensor, install back panel, plug in electrical power, push stove back into position. I used a temperature gauge to check temperature after stove was in position. In my case the temperature had to be adjusted which is a keyboard function on this unit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brant from Saint Paul, KS
- Parts Used:
- 5304445529
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Change Out oven Door Hinges
I first found a video on Youtube and watched it. Then you flip the hinge latch up and remove door from oven. Then remove 2 door handle screws and 4 screws from the bottom of the door. Then remove 2 screws from each existing hinge. Place new hinges on with new screws that came with the kit. Then replace the 4 screws on bottom of door and then the 2 handle screw and place door back on the oven and open door about half way open then flip hinge keepers back up close door and your done.
Was this instruction helpful to you?
Thank you for voting!