91194497992 Kenmore Range - Instructions

0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.

No tools needed, the cap is just held in place with pressure from the wire.

Pulled the range out from wall (which took most on the repair time to do), removed back cover, pulled of terminals, went inside oven a remove the two screws holding Bake element. Inserted new element, tighten down screws, etc.............

1) Make sure unit switches are turned off. 2) Lift Calrod unit up and pull it from electrical receptacle. 3) Withdraw Calrod unit from old bowl. 4) Insert Calrod unit through large hole in new bowl. 5) Push Calrod electrical connectors into receptacle under range top. 6) Seat Calrod unit on bowl rim and insert the assembled Calrod unit and bowl into the hole in the range top.

Removed the old burner bowls, replacing them with the new ones.

Just put 2 screws in. It was simple.
Web site very good details for finding parts.
Fast turn around from order to delivery.
Very satisfied!!!

Removed back cover to look at connections
which were a push on type connector. pulled off
connectors. there is insulation around element
Removed old element, using a nut driver from inside oven. Installed the new element the same way.Reinstalling the connectors, reinstalled the back. less than 10 min. Was very easy !

Just removed the old racks..and replaced them with the new racks...That's all...

Removed burners and existing drip bowls and installed new drip bowls and existing burners took approximately 15 minutes

I checked prices on the internet and found your price the cheapest and ordered the part on a holiday. The part arrived in two days and was installed and back to work pronto. Having worked in sales at Caterpillar Inc for a lifetime, I know how important quick delivery and short downtime is to our customers and you came through for me. I am satisfied with my experience dealing with your company.

I'm so pleased with the ease of placing my order, the price, and the speed of delivery. My only challenge was figuring out the correct part to order, as I didn't have an owner's manual for the range when we moved into the house. But once I located the model # in the range's lower drawer, the website did a good job of guiding me toward the correct replacement part. In my case there was no "repair" involved; I was simply replacing a broken lower oven rack. I would definitely use this company again.

First, I read what other customers posted on this site about how to change the element. =)

I didn't have a nutdriver so I used a pair of pliers instead. They worked fine.

Pulled the stove away from the wall, unplugged it, removed the 4 small nuts holding the small plate over the back of the element connections, slid the connectors off the element prongs, removed baking racks from oven, removed 3 screws holding the element in place, slid element out.

To put the element in I simply did the same thing except in reverse order. The entire process was so easy and only took minutes to complete! However, like another poster, I took the opportunity to clean my oven before putting in the new element.

The best part of dealing with partselect....the element only cost me $51 vs GE site price of $91, Plus the element arrived the morning after I had placed the order! Thank you partselect! In gratitude, I posted my happy experience and a link to this site on my facebook! Thanks for everything!

unplugged stove-removed cover in back of stove-unplugged element-inside oven removed two screws-removed element. reverse procedure to install. took about twenty minutes.
wife happy again.
parts came in two days. I could not believe how fast it came. Thank You very much! Jim Jewkes

turn off power to the stove
Pull the stove away from the wall
remove center (metal) wire cover (5/16 nut driver needed)
disconnect 2 quick connect clips
back to the front of stove, open oven door
using 5/16 nut driver, remove 2 screws
pull out old element
insert new element
using 5/16 nut driver, reinstall 2 screws
go back to the rear of stove
reconnect 2 quick connect clips
reinstall center (metal) wire cover (5/16 nut driver needed)
turn power back on
ready to cook

pull out, push in

I am a recently divorced mom who is too proud to ask for help. When I received the part I took the time to read all of the previous posts. I did exactly as many people suggested: pull the oven out, unplug, clean up since you're back there anyway, used the nut driver to remove the metal plate in back and unscrew the two in the oven, carefully unclipped the electodes from the old element with the needle nose, remove the old element, insert the new element, reinsert the electodes , tighten all nut both in the oven and the large metal plate in back , plug back in, push the oven back in place. I reset the clock and also did what one person mentioned which was to turn the oven on and let heat up for about 20 minutes to burn off any of the manufacture coatings that were on the new element. This did not even take me 15 minutes! I was so proud of myself, I told anyone who would listen! Thank you to all of the men and women who took the time to detail what to do, you made my first repair as a single mom awesome!!