66598002701 Kenmore Range - Instructions

Removed two retaining screws and pulled out coil. one terminal came off readily but one remained and was difficult to get off. Pulled range out from wall and removed cover plate and removed existing terminal connection. Pushed new coil into oven openings and screwed in. Slide terminals on in the rear of range and replaced cover plate. Took about 1/2 hour because I was nervous.

I took the door off and removed five phillip screws from the old bottom support and removed it. I took the opportunity to clean the glass on the front and back before placing it back on. It simply fits into two keepers at top and is held on by the new support at the bottom. I replaced the five screws and put the door back on. It is a simple job that only takes a few minutes.

First I unpluged the range from the power source. Then I removed the back cover, disconnected the two wires to the element, remover two screws on the inside of the oven the held the element in place and removed it. I then installed the new element in the reverse order. This took about one day to get the new part and 15 to 20 mins to do the repairs. I figured that I saved at least $55 on a repairman service call.

remove two screws, remove two slide on wire connections and remove element. reverse to install.

I removed the two screws, puled out the element and took the pliers to unhook the two wires.

replacing this was very easy and simple. I removed the 2 screws holding the support bracket then the 2 screws in back of the elemant ,pull clips off the element then installed it back like it was .....very simple...

Removed the original rack. Checked dimensions, installed the new rack.

Unscrewed the old element. Screwed in the new element.

Put the back of stove on blocks of wood to get high enough to screw the new leg in.

Watched a utube video on replacing element on my model range. Found my Phillips screwdriver. An electric drill would have been a bonus but not necessary. Pulled out range, pulled out plug, removed 1 screw from the lower back cover, disconnected the 2 wires, went to the front and removed oven door and racks, unscrewed 2 screws holding the element. Put new element in and reverse dprocess. Test oven. It worked!!

watched how to video so was prepared for a standard install. removed screws and coverplate...disconnected wires...threaded new element thru coverplate...reconnected wires...reinstalled coverplate with screws. disconnecting and reconnecting wires took some thought and patience, but wasn't rocket science.

Hiring a repair man was going to be expensive, and I saw the part was cheap and others had said this was an easy job to do. I figured I'd give it a shot even though I have very little experience repairing things and there was no help coming from my husband. I followed the instruction of others, unscrewing two screws and pulling the broken element out. The metal that capped the ends of the broken piece needed to be removed. One came off easily. The other took a bit of wiggling to get off. A mistake I made was, by accident, one of the wires coming from behind the stove got pushed back through the hole in the oven wall.. I needed to fish it out with tweezers, but thankfully, that was easily retrieved. Once I put the caps on the new piece, I had some trouble reaching the plate to screw it back into place. I removed the oven door, which helped a lot, but then found it a little tricky to get the oven door back on. Despite the little set backs, I still did it myself in around 15 minutes. I'm delighted to have my oven back without paying a fortune!

Turned off circuit breaker. Unscrewed old element holders from inside broiler - 4 screws. Pulled old element out to expose slip on wire connection at end. R&R with the new one. Screwed assembly back in. Turned on CB and tested. Good to go.

Removed door, dissasembled door cleaned all broken glass, installed new glass, re-assembled door and put door back on oven.

Very simple project.

Removed cooktop, wiring and coil. Marked where wires went on limiter
tabs. Ordered coil 1200 Watt, received a 1500 one. Sent back to PS with prepaid shipping label {great}. New one had a different limiter tab arrangement. The instructions included warned this but doesn't tell you where to put the wiring. Instructions say to remove the old limiter and put it on the new coil but this can not be physically be done plus who would want an old limiter on a new coil.
Found a YOU TUBE video on how to test and place wires on limiter switches which shows the number letter sequence on the ceramic part. Maybe PS will put that info in their instructions. Coil works great !!