79071202705 Kenmore Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Dan from So Lake Tahoe, CA
- Parts Used:
- 5304509706
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Bad oven igniter
It’s a plug in part so other than working on your side while lying on the floor it was a snap. 20-25 mins.
It helps to remove the bottom drawer completely to gain easier access.
It helps to remove the bottom drawer completely to gain easier access.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ralph from SULLIGENT, AL
- Parts Used:
- 316233903
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Never received parts from PartSelect!!!
It went easy, I ordered the part from another vendor, received it in 3 days and it only took about 20 minutes to install.
I do not recommend ordering from PartSelect!
I do not recommend ordering from PartSelect!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alan from SAN MATEO, CA
- Parts Used:
- 316538904
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Repaired Oven Range Light Bulb
The bulb has a plastic clear cover. That cover can just be carefully removed using a screwdriver. It's held in by a metal bracket. After you remove the cover. You'll just need to replace the bulb and then re-install the cover and bracket.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mayola from RIO RICO, AZ
- Parts Used:
- 5304530039
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Broken hoven door handle
Screw the handle, that it...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from Janesville, WI
- Parts Used:
- GRLP3
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Wrench set
No problem, just needed to convert to LP gas.
After looking over the installation instructions I was confident that I could perform this on my own, However, changing the burner orifices was a bit tricky. Getting the original ones out worked well, they stayed in the nut driver when it was lifted. One of the new ones fell out when inserting it. Thankfully it fell all the way down and I could retrieve it. A small piece of tape was needed to keep it in the driver. The rest of the install went per instructions.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marilyn from Clearwater, FL
- Parts Used:
- 316067902
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
I forgot to remove something I had saved in the oven, planning to remove it before using the range.
Very simple. Removed oven rack that had melted residue on it and replaced it with the new one from your company. I want to tell you that the delivery service I received was just geat. Took less than 48 hours to arrive at my home from the time I placed the order on line. Keep up the good work and I will be happy to share my experience with those in need of you services. Thanks. Marilyn Kasson
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Richmond, IN
- Parts Used:
- 5304503232
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Crack in inner door glass
Removed two screws that are attached to handle then removed four screws from bottom edge of oven door. I was then able to remove the outer door glass,this gave me access to the three inner glasses. After removing the retainer for the glass assembly,I was able to remove all three and replace the inner one.I reversed this proceedure to reassemble.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from Ozone Park, NY
- Parts Used:
- 5304503232
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Change on e of the inside glass
removed the screws holding the front part of the door and from there worked my way, untill the third glass.
It took a couple hours, my first time,. Overall easy,
It took a couple hours, my first time,. Overall easy,
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from PORT ORANGE, FL
- Parts Used:
- 5304509869
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Stove was dropped and had broken, bent frame and adjuster feet
New ones fit perfectly. Take a minute to bend the frame straight. Then and I used oversize screws on the replacement parts as the drop had stripped out the screw holes of the frame.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Philip from FREDERICKSBRG, TX
- Parts Used:
- 5304509706
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Igniter failed to ignite propane
Pulled out broiler drawer, removed 3 bolts, plugged in new igniter. Only issue was one of the tiny bolts stripped, so now only have 2 holding it in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from VAN HORNESVLE, NY
- Parts Used:
- 316580611
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Gas stove burners would not ignite.
Ordered spark ignition assembly and followed directions found on YouTube. Went very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jennifer from Santa Cruz, CA
- Parts Used:
- 316442512
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Knob from one of the stovetop burners had cracked and come off
Absolutely simple, new knob fit on without any tools or effort needed. Works great again!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from JERSEY CITY, NJ
- Parts Used:
- 5304509706
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Igniter wouldn't glow and obviously no heat
Partselect always have their install video with the parts they sell so it was easy. I know contractors must not be happy with people like partselect and YouTube with all the instructional videos they supply us with. Keep up the great work partselect.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jalen from GREENWOOD, IN
- Parts Used:
- 5304509706
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
Oven stopped heating all together when turned on.
removed racking, flame cover, and wire plug in cover by pulling out racking, removing one nut, and one screw for the cover. Removed two small bolts to remove igniter, and then unplugged from two locations. Did the same in reverse for install.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bobby from FORT DEFIANCE, AZ
- Parts Used:
- 316237805
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Wrench set
The igniter won't work
On the front left burner would not ignite, after the installation of the new one, same problem, new one didn't fix.. I guess it's something with the electric igniter
Was this instruction helpful to you?
Thank you for voting!