66598003700 Kenmore Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Jerome from RICHFIELD, MN
- Parts Used:
- 74003645
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Broken inner glass window.
Remove the door.
Remove screws
Clear out broken glass. Vacuum out small glass shards.
Clean all glass.
Reattach all parts.
Replace the door.
Smile!
Remove screws
Clear out broken glass. Vacuum out small glass shards.
Clean all glass.
Reattach all parts.
Replace the door.
Smile!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from Whitney, TX
- Parts Used:
- WP7406P428-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Lower bake element burned in two piecies.
First I unpluged the range from the power source. Then I removed the back cover, disconnected the two wires to the element, remover two screws on the inside of the oven the held the element in place and removed it. I then installed the new element in the reverse order. This took about one day to get the new part and 15 to 20 mins to do the repairs. I figured that I saved at least $55 on a repairman service call.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from Bullhead City, AZ
- Parts Used:
- WP7406P428-60
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
element inop
remove two screws, remove two slide on wire connections and remove element. reverse to install.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Fall River, MA
- Parts Used:
- WP7406P428-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Element burn out
I removed the two screws, puled out the element and took the pliers to unhook the two wires.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jane from BRYAN, TX
- Parts Used:
- W10823711
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
Back left burner went out
I found on youtube Also we marked each wire with masking tape 1A and 1B, 2A and 2B. The wires were the same color.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lynn from HAZELWOOD, MO
- Parts Used:
- WP7406P428-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
lower burner element wasn't working
watched how to video so was prepared for a standard install. removed screws and coverplate...disconnected wires...threaded new element thru coverplate...reconnected wires...reinstalled coverplate with screws. disconnecting and reconnecting wires took some thought and patience, but wasn't rocket science.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from Lewiston, ID
- Parts Used:
- 74003645
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Broken Inner Glass Pane
I received my glass panel realy quick from Part Select. It was an eansy job to install the new pane.
It took less than an hour. Thanks for Your prompt service.
It took less than an hour. Thanks for Your prompt service.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jaime from Deltona, FL
- Parts Used:
- W10823711
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Elements burned wouldn't heat
First I cut electric power off removed the two screws that hold glass top lifted up and removed two screws that hold element in place. I disonnected the wires and then pulled the element out
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nathan from Oak Creek, WI
- Parts Used:
- WP74011768
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Replaced the Handle on the Range Door
After the repair I determined that the door did not need to be removed from the stove. The top 3 screws needed to be taken out, the front clase needed to be slid out by pushing it right to left or left to right. Then the bracket that held the inside screw assembly needed to be removed. The new handle needed to be installed and the bracets put back into place. The front glass needed to be reinstalled right to left or left to right. The hardest part of my install was putting door back on the range, the hinges kept popping out of place before setting into the range. The best way to replace the hangle would be to not remove the door from the range.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chris from Lebanon, TN
- Parts Used:
- 74004566
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Inside glass shattered during clean cycle
Removed door, dissasembled door cleaned all broken glass, installed new glass, re-assembled door and put door back on oven.
Very simple project.
Very simple project.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rosemary from Louisville, KY
- Parts Used:
- WP7406P428-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
the element was fried in half
only 2 screws held the element in place pulled the wires and replaced with the identical part very easy to do and thanks for having the part available
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- lou from spring grove, IL
- Parts Used:
- WP7406P428-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven wouldn't heat
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires.
Installed new element . Connected two wires pushed in place install the two screws.Done....
Installed new element . Connected two wires pushed in place install the two screws.Done....
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cynthia from Ellicott City, MD
- Parts Used:
- WP7406P428-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Lower element burnt out.
This was really easy. I took out the lower oven racks. Most important - Turned off the breaker to the stove. Unscrewed the element and popped it out. Put in the new one and screwed it back in. Turned on the breaker and I was ready to go.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lawrence from Lakeport, CA
- Parts Used:
- WP7406P428-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Element Wouldn't Heat
I removed the two screws that hold the element in place, moved it out to expose connecting wires, then removed wires and put in new element.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Deborah from PATASKALA, OH
- Parts Used:
- WP7406P428-60
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Heating element burned out
Took the element out & cleaned the oven & put the new element in. Easy as pie.
Was this instruction helpful to you?
Thank you for voting!