79092312307 Kenmore Range - Instructions

took screws on outer sides and then removed glass put in new glass replaced screws done

Very simple with instructions supplied, Removed two screws inside on back of door, then removed four more screws to get to inner glass,removed broken glass installed new glass, replaced all screws.Job completed. very good instructions,Thank You.

To find problem. I turn the power off to range. Removed top back panel. Removed switch and found there was a black spot on white covering of switch. So I order a switch. When it came I turn power off to range. Removed the top panel on back of range. Removed one wire at a time and put it on the new switch. Once all wires were on new switch. I removed old switch and installed new one. I then reinstalled the top back panel and turned the power back on. It is really easy to do. If you are not confident enough. Take a picture of the back of range before removing the panel. Then take a picture of the wires before you remove them.

Easy to put in but i droped a screw to hold the element. had to pull another screw to fix it

Took back cover off 2 screws held the switch then moved wires one at a time from old switch to the new one put everything back plugged in stove everything worked

Took the back off and replaced the switch for that burner. Got alittle nervous because the switch did not look the same and the connectors were labeled differently, but it worked. Lost the red light button some how during the repair so when I turned the stove on sparks came out the back because the light connector was loose so I did have to order another one of those.

Bought a electric range/oven with a broken glass in the door cheaply because the owner didn't think they could fix the glass. I watched the video on You Tube on how to handle the spring loaded hinges and followed the steps as presented. The toughest part of the job was cleaning all the crud on all of the glass due to the gap in the inner glass. I had to use a square drive and a phillips head screwdriver to disassemble and reassemble the door. It took less than 30 minutes to complete the job and most of that time was cleaning the glass.

I disconnected the power cord,took the top back plate off,the switch knob on the switch I was to change,the two screws holding it.pull the old switch out,place the new one in the holder,replaced the two screws that holds the switch and took the wires off the old switch one at a time and placed them on the new one in order on new switch.replaced the back cover and plugged power cord back in.turned range on,it was good. r taite,

I watched you vedio and done just as the vedio told me how to change the switch. When I got the switch on pluged it in turned it on and every thing work great. thank you very much.

Replaced the control I got from you , even though it was a little different the lugs matched up and works great.

Screwed up by not shutting breaker. Shorted out 3 switches. Thought i could get away without shutting breaker that was a costly error. No problem replacing the 3 switches and element switch. Took about 1/2 an hour.Always shut breaker before doing any electrical repairs.

watched the veido first then un pluged the stove then i took out 6 screws and 2 from the switch and reversed every thing

Would have been simple if Frigidare had not changed the plastic snap wire connector on the part. The replacement part had a different snap together wire connection. After a couple of phone calls stating that the new part and the old part had different part numbers was informed that you have to snip off the ends and use wire connects but it was the right part. Once I knew that it was a simple repair if you have the wire connects to connect the wires.

Unplug the range, pull the knob off the front. Remove the screws from the cover plate behind the switch and remove the cover plate. Carefully pull one wire at a time off of the old switch noting the markings: "L1," "L2," "H1," etc., as the wire position may be different on the new switch. Put each wire onto the new switch as they are removed from the old one. Let the new switch hang from the wires while removing the 2 Phillips head screws from the front of the old switch and remove the switch. Hold the new one in place, start both screws, & then tighten them. Push the knob on the new switch. Plug the range in and try it. If everything works, install the rear panel and screws. I think that it took me longer to type this than it did to actually do the job.

Unplugged the main cord to the socket in behind range. Took back panel off. Unscrewed switch from its position on face of range. Switch is not a look alike switch to original, so had to pay attention to the labeling on both switches as to their identity. Removed one line at a time from old switch and placed on new switch. Rechecked positions of the wires and made sure there was no binding of the wire positions when installed. Mounted switch to same position previous switch was removed. Reinstalled back panel, plugged in range and tested switch. Very easy repair as long as you can see the labeling on back of switches. I used a light having a strap that is positioned on my head for best lighting possible for one person repair.