91195288891 Kenmore Range - Instructions

I removed the 2 screwws inside the oven cavity and pulled the element towards me. I unplugged the wires from the element and plugged in the new one and secured it in place with the 2 screws.

Shut off electrical supply to stove.Remove 2 screws.
Slide element out enough to remove connectors from element.
Position new element.Slide connectors onto new element.
Slide element back into position.Replace 2 screws.Turn on electrical supply.

Turned off the breaker to the stove, removed oven racks, used small pair of plyers to remove bolts (2) holding defective element in place. Pulled (2) wires that had a snap connection apart. Old element was not removed. Connected (2) snap wires, pushed them back into the oven wall, used plyers to re-connect the element to oven. Installation DONE!
Turned on breaker and then the oven; we are now baking again.

It was real easy all I had to do was turn the breaker off,Undo two srews and disconnect the two wires. Then repeated the process to install

The replacement element came within a couple of days of our order. From the time I saw it by the front door till the repair was complete was about 10 minutes. Half the time was taken in walking to my tool box. In just a few minutes we had tested the new element and were ready to make dinner. Great value for the price.

First i turned off the main electricity for the oven. Then I removed the two screws with my socket wrench. Then i pulled the element out about 3 inches then disconnected the 2 wires that heated the element. I simply reversed the process to put in the new bake element and i was done.

Took out the hexagon screws, used pliers to pull the connecting ends apart, slid in the new element in to the connecting slots, reattached to screws, turned on the oven to see if it would heat up and it did. It was really easy. I had waited for a week to get the part from my local Sears parts house. You sent it out and I had it in 3 days. They still don't have the part. Thanks so much.

I had grease on the baking element when I turned the oven on. I thought it would burn off, it caught fire and destroyed the baking element. I ordered a new element, it came within two days. I didn't wait for my husband to come home. I got a screw driver, took off the screw, used pliers to pull apart the old baking element from the wires. I did this carefully , our oven is old and the element was not pulling away easily. I inserted the new element, put the screws in and it worked perfectly! I was very proud of myself but the truth is that this is a simple job.

Watched youtube....

Removed the two screws pulled out the old element and slid the new element in and put the screws back in. I used it that night to bake supper

The hardest part of repair was moving the oven from the cabnets to unplug and gain access to rear of oven. Remove rear cover panel unplug two spade connectors attached to the heating element. Open oven door and remove the two screws holding the heating element to back of oven. Pull heating element out. Then slide the new element in and assemble in reverse order.

I turned the power off.Pushed on the terminals,and used a nut driver to secure the element to the oven back wall.Great service.I recieved the part in 24 hours with reg. shipping at a great price,Unbelieveable!!!

pulled out oven, unplugged power. Removed back cover for element, disconnect old element. Moved to front of oven and removed the two screws that held the old element,removed old element. Installed new element, connect element, installed cover, reconnect power.

I followed the directions in the video on the website. The repair was so easy!! I simply unscrewed the screws holding the element in place at the back of the oven, pulled the wires out. This did take a little bit of time, as I didn't want to pull the wire off of the element and lose it in the back of the oven, but I was able to eventually work it free from the insulation and make the connectors visible. I slid off the old element, slid the wires back on to the new one and pushed them back into the wall of the oven and replaced the screws. Works like a charm!! I will definitely use your website for other appliance repairs!!

Pulled oven from wall, Unplugged oven from outlet, Took 5/16 nut driver pulled back cover off oven to expose the quick connect wires, Pulled wires off old element, Opened oven door took the 2 screws off bracket on back of oven, Removed old element, Put new element in place, Put the 2 wires back on, Buttoned back up check to see if worked it did ((: