79078521401 Kenmore Range - Instructions

We removed the old part and replaced it then when warming the oven all of a sudden there was a loud noise and something went and so we called a repair man which I guess we should of done in the first place. Now he has ordered a part that cost 170 soo that is my story don't try to repair if you don't have experience.

Watched the you tube video from this website and did the same to my own oven. Much better replacement igniter than was installed in oven from factory and amazing packaging from partselect.com. Thank you!

Removing the drip pan and the bottom burner cover exposed the igniter, removing two screws retaining the bracket freed the old igniter. Removing the warming drawer allowed access to the control module to unplug the wiring on the ignitor. After making myself a diagram, I unplugged the wires and removed the malfunctioning igniter. Cutting the leads off the old igniter long enough to splice it on below the oven bottom with the enclosed wire nuts and attaching the new igniter (reusing the old insulation to protect the wire) took only minutes and reassembly was straightforward.

New igniter: $60
Repairman fee saved $150
Being able to tell my wife "See,
I told you I could fix it!" PRICELESS

The bulb has a plastic clear cover. That cover can just be carefully removed using a screwdriver. It's held in by a metal bracket. After you remove the cover. You'll just need to replace the bulb and then re-install the cover and bracket.

See other posts.... they have the correct repair procedures.

HIGHLY RECOMMEND removing the bottom drawer to access the space where splice will be made between new igniter wires and existing wires. This step is recommended in previous posts. I wasted a lot of time taking out unnecessary stuff in the oven compartment before I realized that the drawer compartment provided easy access for repair. Story of my life on just about all repairs.

Was easy...I pulled oven out from the wall so I could get to the back.i used a nut driver to remove small silver cover.matched up wires to the never module and re installed.pluged oven back in and burners lit perfectly

Remove bottom plates and deflector from oven, remove old igniter. Remove bottom drawer and panel to expose wiring. Cut wires, used supplied wire nuts to splice. The time consuming part of this job was having to clean all the parts before reassembly, and having to extract screws that were rusted into place due to heat and spillage. One of the igniter screws was stripped, and was very difficult to remove. The first part in your "probably cause" list was the right one! Thanks for the good service, and a useful website!

Very easy just had to pull the wire up that holds it secure.

Disconnected power cord to range
Removed the cover over the flame guard
Removed the Flame guard
Pulled out broiler drawer
Unscrewed the cover and disconnected the white plastic connector to the ignitor wires
Un crewed the two small screws to the ignitor and removed the old ignitor
Cut the two wires from the old ignitor
Connected the new ignitor to the wires on the white connector
Installed the new ignitor
Reassembled parts dsassembled
Plugged in power cord

Works

1- put in new thermostat 2- put in new gas valve 3- put in oven igniter ....3rd time a charm. Now I have all new oven parts! My husband installed and said it was pretty easy, have to take the oven door off and inside bottom out.

On the front left burner would not ignite, after the installation of the new one, same problem, new one didn't fix.. I guess it's something with the electric igniter

New ones fit perfectly. Take a minute to bend the frame straight. Then and I used oversize screws on the replacement parts as the drop had stripped out the screw holes of the frame.

Replaced the ingintion module, still did not work, replaced the burner complete with new ingiter , it now works but another one quit . the front right one has 5 ohms resistance ,replaced with new one with 0 ohms, the back left has 2 ohms resistance and now it does not work , will need to replace that burner allso. too bad you can't buy just the spark module for the burner.

Oven would not light upon setting for oven heat-up. Igniter would glow, but no gas flow. Gas Valve safety not sensing enough current draw from igniter to open gas valve. Original igniter measured 175 Ohms on Volt-Ohmmeter. New Igniter measured 74 Ohms before installation and use. Installed and spliced into existing wires using good quality wire nuts and tucked wiring into wire areas ensuring it was away from burner flue. Oven lit on first start-up! Problem fixed! Easiest to get to by removing broiler drawer, pressing catch tangs in from outside rails using a small screwdriver. 1 screw of 2 on igniter mount was stripped and difficult to remove, but working with pliers and nut driver was able to remove it with some difficulty. New Igniter hangs fine with 1 screw. .

Remove oven racks and bottom oven panel cover.Removed old igniter.one screw was stripped so that slowed me down quite a bit! Used a small vise grip tool to remove screw! installed new ignighter,cut existing wires; spliced in new wires( be sure to unplug appliance) tested ok. Reassembled.