79071211703 Kenmore Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Neal from Warsaw, IN
- Parts Used:
- 5304503232
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
broken inner glass
Removed oven door. Removed screws from bottom of door as well as handle screws. Remove inner panel to expose glass. Replaced glass panel and reverse steps. Very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marc from Gastonia, NC
- Parts Used:
- 316220729
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Broken control panel housing
I actually had to buy two parts, the cover and the control panel. But unfortunately I could not get them from the same place. But I replaced the control panel and the cover in about 15 minutes. No issues. Everytihg lokks brand new and works like a new stove. So I am very pleased.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- charles from El Paso, TX
- Parts Used:
- 316067902
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Just had to replace the racks in the stove.
Did just want to comment on the customer service. It was great. The easiest to order that I have ever dealt with. Received prompt attention to the order and processing the same. JUST GREAT> Thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from Provo, UT
- Parts Used:
- 316112005
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Needed to install an anti-tip bracket on my stove.
Moved the stove. Used the template to position the bracket. Put the supplied screws to attach bracket to the floor. Slid stove back into place. DONE!
Was this instruction helpful to you?
Thank you for voting!
burned up burner
the wrong parts list came with the stove, so the part I ordered didn't fit. The people at partselect were great to work with.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- June from Mt. Vernon, AL
- Parts Used:
- 316067902
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old rusty worn out oven racks
Removed the old oven racks and put in the new ones.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Fanny from Alhambra, CA
- Parts Used:
- 316468601
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
I had the top trim broken on the oven door.
Very simple repair. I received my part a few days after placing order; then installed it myself. Anyone can do this simple easy repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- steven from Daleville, AL
- Parts Used:
- 316233903
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
No heat from bottom or top element,k stove top and clock all worked fine.
Timer was bad. Removed the four screws on the rear panel, and then the four screws holding the timer in place. I let the old one dangle by the wires until the new one was in place, then just switched the wires one at a time. There is one set that has a plastic connector, and you need a small flat screwdriver to depress the locking tab on the top of the connector to release it. Be sure and order a new face plate as the old one will not come off without tearing. Re-install rear cover and your done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Manasquan, NJ
- Parts Used:
- 316495901
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Bottom Panel of over rusted out.
Unplug the stove from the wall socket. Remove the oven door as shown in the instructions for replacing the door. This makes the job a lot easier. At the rear of the bottom panel there is a screw at each corner. Remove these screws, a screwdriver will loosen them, then remove by hand. If you have a convection oven remove the fan cover as this prevents the bottom panel from coming out. There is a screw at the top and the bottom of the cover. You can then gently lift the bottom panel at the rear and work it out of the front lip. Install the new bottom panel in reverse order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Matthew from Gladwin, MI
- Parts Used:
- 316237805
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Wrench set
burner would not light
We took off all of the bolts holding the burner assembly's in place . Then took the top of the s range off. Used a wrench to remove the old assembly and re-placed it with the new one. It took longer to get all of the top and under cover off then to put the new part in. Very good service from Part Select. MATT
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Buffalo, NY
- Parts Used:
- 5303935200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Replaced front oven door glass
I unscrewed the two screws at the bottom of the oven door to remove door,placed on a flat surface I removed the two screws located by the handle.The oven separates into two or three pieces.I cleaned the exterior lip where the glass goes with a putty knife to remove any debris.I placed the aluminum foil,(which comes with the new window)two squares in lower corners and strips up both sides.I re-screwed everything together and all done...P.S. do not order the aluminum foil,it comes with the new glass.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ricardo from Brooklyn, NY
- Parts Used:
- 5304509706
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
The Oven ignitor did not turn spark for the oven to turn on and heat up.
I pulled the top cover from inside the oven off and unscrewed 2 screws to remove the heat plate. After i unplugged the adapter for the old ignitor apart and unplugged 2 wires and removed 2 screws that hole the ignitor to the plate. i replaced with the new ignitor, screwed back in place , plugged the 2 wires and the adaptor plug in and i was done , in less that 30 mins.. I also saved $180 (Sears $260) on this do it yourself repair.. Thanks PartSelect for having the part in stock.... R Diaz (Bklyn N.Y.)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- BARBARA from NORTH PORT, FL
- Parts Used:
- 316233903
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
no heat in oven
replaced temp probe per your suggestion. No improvement! checked both heating elements with ohm meter. OK Next suggestion was replace circuit boards. Bought new range for less than cost of 2 oven/range control boards.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steve from Hiram, OH
- Parts Used:
- 316233903
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
oven wouldn't work
Pulled stove away from the wall and unplugged it. Removed probe and cut the wires because the connection clip on the new probe was different from the original. Leave the wires as long as possible because you will need the extra length to splice the clip from the old probe to the wires on the new one. Replaced probe and plugged the oven back in. Done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Greenville, TX
- Parts Used:
- 316239700
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Gasket In Door Replaced
The gasket just snapped in place. The first one I ordered was, my fault, the wrong one and I returned it and got the correct one two days later.
Was this instruction helpful to you?
Thank you for voting!