79092109010 Kenmore Range - Instructions

All I had to do was loosen the screws, pull out electrical hookup on both ends, hookup new heating element to elecric and screw em into place. That's it, super easy and I got the part in 2 day : )

this bake element has two special Hex style screws, securing it in place, but a nut driver worked just as well. remove the baking racks, and then loosen the two hex screws. slowly pull the element out of the back wall and then disconnect the electric leads. reinstall by doing then the opposite action. could not have be simpler.

I looked for the proper part on this site. I was even able to find a video on how to install the part. It was great to see the step-by-step directions and tools needed. I ordered the part. It came quickly so that I was able to get my oven repaired before my kids came home for spring break. The only problem I had was the old screws were really stuck on. I used some WD-40 and they were still quite stuck. I learned that by gently going back and forth with the nut driver, rather than just trying to turn in the correct direction, that the screws came out quite easily. I felt so proud to be able to fix my own stove and save money in the process! Very satisfying for a single mom. Couldn't have done it without the video directions.

Turned off power to appliance removed the screws connecting the element. Disconnected the wires from the old element connected the new element replaced the screws and tightened turned power on turned power back on heated oven to be sure it worked. Very simple to do.

was easy open the back side of the range and change the part, the only issue was the wire I used the diagram

first thing was to turn the breakers off. then pull the range away from the wall. used an 1/8 th inch socket to take off the back panel to get access to the switch.used a Phillips screwdriver to disconnect the switch under the knob in the front. took off the wire terminals one at a time and matched it to the numbers on the old switch.replaced the knob, screwed it on to the range. turned the breakers on and tested the switch.worked fine, replaced the back cover and pushed it back into place.

I had to replace the switch on one of the large elements. It could and should have been a quicker repair if there would have been some installation/wiring instructions included with the part. Other than that the repair went well.

I pulled the oven away from the wall, unplugged the cord, removed the back panel then removed the screw from the old sensor.

d

Take handle off, then back cover. Of course unplug power. Switch wasn't built exactly like the original but all you have to do is connect each wire to the same letter, number code as on the old one . Works like brand new!

My part was the oven burner for my Tappan stove. I followed a very helpful you tube video. All I had to do was use 1/4" screw-type screwdriver (not sure what you call it), remove screw, pull out each side, pull part away from wire; and then insert the new oven burner!! SIMPLE and I'm a 68-year old widow! I was proud.

Removed the screws, replaced it with the new bake element, put the screws back in........and bam! I'm back in business. That's how easy this was to repair. Bake element cost me 40 bucks, appliance repair shop wanted about 200 bucks to repair.

Replaced the switch very easily! Working great

I flipped the 220 circuit breaker to shut off the electricity. I unscrewed the old element (2 screws). One problem I ran into was that there was insulation packed tight around the old wire, so when I went to pull it out one of the connectors came undone. So I had to take the small plate off the back of the stove and fish the wire back through. I connected the new wires and screwed the element to the back. I only needed a square head screw-driver for the whole job. It would've taken me 5 minutes if I wouldn't have had to fish the wire back through. Still, it only took around 20 minutes and was really easy. The element cost me less than half of what an appliance repair shop charged. I'm a woman, and I've never attempted anything like this before but the video made it so easy to do! Thanks for saving me a bundle of money!

Removed the defective part. Install the new part, insert the connectors. Now its working