79091312012 Kenmore Range - Instructions

Followed video instructions on your web site.Removing one wire at a time as suggested simplified installation.Somehow i lost burner lens indicator.Ordered it from your website cost $3.84 plus shipping recieved in one day. GREAT SERVICE

Large burner would cycle on and off per temp setting a few times. Then it would stick on high. Read other problems people had with the burner switch, which helped to determine the problem. Instillation per video was pretty straight forward; but the issue I ran into was when pulling off the wires from old switch, there was a short wire which connected to the indicator light. The abrupt release yanked the wire which caused the lens indicator to snap. So, when you are repairing the switch, be aware if there is enough slack in the wires to prevent that issue

Pulled the stove away from the wall, disconnected the power cable, removed the top part of the back where the switch was. In front there are two screws that are philip heads that hold the the switch in place. Be careful when replacing the wires. When you take one wire off, place it on the new switch in the the same position. The switch can be put back, but be careful of the angle, because it has four screw holes. Replace the switch, replace the back, plug the power cable in, and push the stove back to it's original position. Make sure there isn't anything on the burner when you test the switch.

Removed bottom drawer. Pulled Range out away from the wall. Unplugged Range. Removed 6 screws from top back cover. Removed top back cover to reveal the Infinite Switches behind the knobs. Pulled the knobs off of the Switches I wanted to change. Removed the 2 Phillips Head screws holding each switch. Pulled the wires off of the old Infinite Switch and put them on the new Infinite Switch. I was careful to put each wire on the correct terminal from old to new switch. I then reassembled the Range in reverse order. I changed both 8" Burner Infinite Switches. I was only having trouble with 1 switch. But, upon inspection. Both Switches had burn marks on the top left of the switch.

Very simple, just removed three screws and pulled the top out and turned over and then removed the two screws holding the support bar. Removed and installed the element.Surprised to see that the element burned out in such a short time.

Replaced control units that were malfunctioning.

Disconnected power first. Removed 4 screws on the back of the range, pulled the knob off of the switch, removed 2 small screws on the switch(on the front , under the knob) pulled off the 4 wires with spade connections on the switch. Put wires on the new switch, put in 2 screws on new switch, pushed knob on switch, replaced back cover and tested the new switch. Works great. Took less than 10 mins.

After turning off the power to the unit, we took it out of the countertop and unscrewed the base of the unit. We then unplugged the damaged coil and plugged in the replacement part. We then screwed the base of the unit back on and replaced the unit in the countertop. The largest burner now works.

The gasket just snapped in place. The first one I ordered was, my fault, the wrong one and I returned it and got the correct one two days later.

Took the back off and replaced the switch for that burner. Got alittle nervous because the switch did not look the same and the connectors were labeled differently, but it worked. Lost the red light button some how during the repair so when I turned the stove on sparks came out the back because the light connector was loose so I did have to order another one of those.

We removed the back of the stove, unscrewed switch from the stove face and unplugged the wires from the old switch. The new switch was universal so I had to follow the numbers by the prong on the old switch to determine which was the correct prong to plug the wires, plugged them in, screwed the switch back to the stove face and replaced the back Viola all fixed.

Pulled stove away from the wall and unplugged it. Removed probe and cut the wires because the connection clip on the new probe was different from the original. Leave the wires as long as possible because you will need the extra length to splice the clip from the old probe to the wires on the new one. Replaced probe and plugged the oven back in. Done.

replaced temp probe per your suggestion. No improvement! checked both heating elements with ohm meter. OK Next suggestion was replace circuit boards. Bought new range for less than cost of 2 oven/range control boards.

Timer was bad. Removed the four screws on the rear panel, and then the four screws holding the timer in place. I let the old one dangle by the wires until the new one was in place, then just switched the wires one at a time. There is one set that has a plastic connector, and you need a small flat screwdriver to depress the locking tab on the top of the connector to release it. Be sure and order a new face plate as the old one will not come off without tearing. Re-install rear cover and your done.

watched the veido first then un pluged the stove then i took out 6 screws and 2 from the switch and reversed every thing