62960009600 Kenmore Range - Instructions

Hiring a repair man was going to be expensive, and I saw the part was cheap and others had said this was an easy job to do. I figured I'd give it a shot even though I have very little experience repairing things and there was no help coming from my husband. I followed the instruction of others, unscrewing two screws and pulling the broken element out. The metal that capped the ends of the broken piece needed to be removed. One came off easily. The other took a bit of wiggling to get off. A mistake I made was, by accident, one of the wires coming from behind the stove got pushed back through the hole in the oven wall.. I needed to fish it out with tweezers, but thankfully, that was easily retrieved. Once I put the caps on the new piece, I had some trouble reaching the plate to screw it back into place. I removed the oven door, which helped a lot, but then found it a little tricky to get the oven door back on. Despite the little set backs, I still did it myself in around 15 minutes. I'm delighted to have my oven back without paying a fortune!

watched how to video so was prepared for a standard install. removed screws and coverplate...disconnected wires...threaded new element thru coverplate...reconnected wires...reinstalled coverplate with screws. disconnecting and reconnecting wires took some thought and patience, but wasn't rocket science.

Turned off circuit breaker. Unscrewed old element holders from inside broiler - 4 screws. Pulled old element out to expose slip on wire connection at end. R&R with the new one. Screwed assembly back in. Turned on CB and tested. Good to go.

First I cut electric power off removed the two screws that hold glass top lifted up and removed two screws that hold element in place. I disonnected the wires and then pulled the element out

replacing this was very easy and simple. I removed the 2 screws holding the support bracket then the 2 screws in back of the elemant ,pull clips off the element then installed it back like it was .....very simple...

Went well. Husband, who has some appliance repair experience, did repair in less than a hour. Replacement burner was not an exact duplicate of original but he was able to adjust for that.

Access to burner nothing like on-line videos:

1) Remove 4 screws under front control panel. (Oven door needs to be open.)
2) Remove 2 flat head screws on sides of control panel. This will loosen control panel. Capture control panel to keep from hanging from wires/connectors. I used hooks made from a wire hanger.
3) Remove 2 screws to remove two steel panels on either side of stove.
4) Remove rear screw of the 2 front screws now exposed and 2 rear screws near top of stove.
5) Carefully flip over glass top being careful not to pull on the wires.
6) Identify burner to be replaced. Note 2 numbers where two clamps are attached to burner.
7) Using 3/8” nut driver, remove screws to allow removal of burner. Remove wires per included instructions. Remove burner.
8) Place new burner under clamps and align to the holes by the two numbers noted in step 6 above.
9) Connect wires to new burner as per included instructions.
10) Reverse removal steps.

Looked at parts blow-up, watched a You-Tube video,

Had to remove 4 small rusty screws and a sort of guard made of metal. With power off, I had no light to see way in the back of the oven. Suggest use of a head-lamp.
Also, it would have been very helpful if when the part arrived, it was noted somewhere that a smell and “smoking” from the part is very normal. This would have saved me a tremendous amount of stress and more days without the broiler trying to figure out if I did something wrong, if the part was bad or other. Sounds so simple, but BOY, that would have been SO helpful

Removed cooktop, wiring and coil. Marked where wires went on limiter
tabs. Ordered coil 1200 Watt, received a 1500 one. Sent back to PS with prepaid shipping label {great}. New one had a different limiter tab arrangement. The instructions included warned this but doesn't tell you where to put the wiring. Instructions say to remove the old limiter and put it on the new coil but this can not be physically be done plus who would want an old limiter on a new coil.
Found a YOU TUBE video on how to test and place wires on limiter switches which shows the number letter sequence on the ceramic part. Maybe PS will put that info in their instructions. Coil works great !!

I found on youtube Also we marked each wire with masking tape 1A and 1B, 2A and 2B. The wires were the same color.

I checked out Maytag.com - found the parts page on my computer - found the top oven element - ordered it from Part Select - it arrived just a few days later......

Before it arrived, I removed the damaged electric element from top of oven - easy.

Oven was ready for me to install new element - the video on your website was perfect - it helped me remove the old & install the new element from Part Select. It took me about an hour.

Thank you for your fast service, good instructions & the video!

I'm an 84 year old female. Did this by myself! Thank you!

I received my glass panel realy quick from Part Select. It was an eansy job to install the new pane.
It took less than an hour. Thanks for Your prompt service.

only 2 screws held the element in place pulled the wires and replaced with the identical part very easy to do and thanks for having the part available

This was really easy. I took out the lower oven racks. Most important - Turned off the breaker to the stove. Unscrewed the element and popped it out. Put in the new one and screwed it back in. Turned on the breaker and I was ready to go.

I removed the two screws that hold the element in place, moved it out to expose connecting wires, then removed wires and put in new element.