79094453700 Kenmore Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- TRACY from NEW PHILA, OH
- Parts Used:
- 316490000
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Oven would not heat or sometimes hold heat to set temp
I was able to find the most common reason for my oven's symptom by searching online. I searched for the part I needed but was not confident that I would get the correct part until I looked on partselect.com. After verifying the part number with my owners manual and looking at the video on their website, I decided to order. PartSelect shipped the part as expected, and I was able to install it in less than 30 minutes. The only tool needed for installation was a nut driver. My oven is now working like new.
Many thanks to PartSelect for their comprehensive website and fine service.
Many thanks to PartSelect for their comprehensive website and fine service.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from ELKHORN, WI
- Parts Used:
- 316490000
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
run away temp
I changed the temperature sensor and tried again. The stove again went on temp runaway and it was suggested to replace control board which is out of stock.
I will have to toss out this stove and buy new as you and no else has this part.
I will have to toss out this stove and buy new as you and no else has this part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from TULSA, OK
- Parts Used:
- 316203301
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Broiler element fried, found nothing in town, Part Select delivered in three days
Pulled oven out, took the screws out of back plate cover plate with socket wrench, pulled connectors out through the back, removed the door, pushed the element rods through the two holes, connected the two wires, screwed the element in, put the hangars on for the element, put the back plate on and turned the broiler on, worked great, put the range door back on and has been working great. Great company, hope not to use them again, but good to know they are there with my part.
Gary H.
Gary H.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kimberly from OWASSO, OK
- Parts Used:
- 316490000
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Oven temperature was not consistent.
I pulled the oven away from the wall, unplugged the cord, removed the back panel then removed the screw from the old sensor.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- German from Houston, TX
- Parts Used:
- 316436001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
I could can not control the burner
was easy open the back side of the range and change the part, the only issue was the wire I used the diagram
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lisa from APACHE JCT, AZ
- Parts Used:
- 316282100
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
There was no instructions. The wires don't match up old vs new. I read the reviews and this helped.
However the 1a 1b etc. Are very hard to see thus the need to magnify. Then it was easy.
I must say the guy I talked to was very nice.
I must say the guy I talked to was very nice.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from NEW HYDE PARK, NY
- Parts Used:
- 316436001
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The switch wasn't working on all the different settings.
first thing was to turn the breakers off. then pull the range away from the wall. used an 1/8 th inch socket to take off the back panel to get access to the switch.used a Phillips screwdriver to disconnect the switch under the knob in the front. took off the wire terminals one at a time and matched it to the numbers on the old switch.replaced the knob, screwed it on to the range. turned the breakers on and tested the switch.worked fine, replaced the back cover and pushed it back into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gregory from American Fort, UT
- Parts Used:
- 316436001
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Burner switch had gone bad.
I had to replace the switch on one of the large elements. It could and should have been a quicker repair if there would have been some installation/wiring instructions included with the part. Other than that the repair went well.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Florence, OR
- Parts Used:
- 316436001
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Burner was inconsistent the heating with red hot one minute and not the next minute
I watched the video on how to do it
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from MOUNT VERNON, ME
- Parts Used:
- 316436001
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Burners constantly overheating, and inconsistent heating.
With the stove pulled out and unplugged, There are 4 square head screws to pull a metal plate off the back of the range. Once that is off, the infinite switches are in line and can be removed with a philips head screw driver/bit. I placed each wire onto the new switch as I removed them from the old, to avoid any confusion. The entire repair took less than 10 minutes. Incredibly easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Theresa from MOORESVILLE, NC
- Parts Used:
- 316505601
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Replaced bottom panel
Unscrew two very visible screws located in the back of the oven holding in the panel. Remove panel. Install new panel. Replace screws. Could have used new screws but didn’t have any.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Austin from GROTON, CT
- Parts Used:
- 316505500
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- Less than 15 mins
Bake element not heating correctly
Started with trying to take the door off for easier access to heating element.
I ended up lifting the door off and the front glass shattered and I sliced my hand open.
Ended up buying a new oven/range.
I ended up lifting the door off and the front glass shattered and I sliced my hand open.
Ended up buying a new oven/range.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rhonda from PACHECO, CA
- Parts Used:
- 316404002
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
wrong part received and returned
I wanted the bracket for the oven heating element and received the bracket for the broiler.... part returned and now I am stumped about what my next move will be
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anthony from LEWES, DE
- Parts Used:
- 316278800, 5304409888
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Old terminal block was melted
removed back panel on range, removed old terminal block installed new terminal block, replaced back panel cover.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- adolfo from new york, NY
- Parts Used:
- 316436001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
The element gets very even the control is at minimum
Removed the defective part. Install the new part, insert the connectors. Now its working
Was this instruction helpful to you?
Thank you for voting!