79046594502 Kenmore Range - Instructions

Turn power to range off at electrical panel. Loosened control panel exposing switch. remove old switch and replace. reassemble.

After trying to unscrew a plate on the side, I found that would NOT work at all, the side panel of the stove was behind it. I found a tab that cut-out on 3 sides just above the location of the recepticle, and simply bent that tab out, pulled out the old recepticle, slid in the new recipticle, and put in the screws and then bent back the tab. It was sooo easy once I found that. I repeated in on the other side.

Took 3 panels off to get to the electric block. Replaced electrical block and put it back together. Still no change.

Easy as 1-2-3

Removed 2 screws holding old temperature sensor inside the oven and gently pulled out the wire till the connector came through the hole. Disconnected old probe and attached new one. Fished the wire back in the hole and replaced the two screws. Then followed the operating instructions for calibrating the oven. Ended up setting it +5 degrees. So far, works great.

Husband made install in very short time. Nice to have them back in operation.

open door,throw the door latches at the hinges and remove door. Take the out of the outer panel so you can separate the glasses. remove clip that hold the outer glass in place. I ordered a replacement glass as I never thought that it would come clean it looked so bad, but it cleaned up like new so I now have a spare glass for my oven door. Just reverse the way you take it apart to put it back together.

Turn off the breaker! Remove the switch knobs. Using a Phillips screwdriver remove the two screws on the affected switch. With a large tip Phillips remove the three screws at the edge of each end of the panel and place it bottom side up on the stove top. Look at the bottom of the switch. Compare those numbers with the numbers on the new switch. Remove the wires one at a time and place them on the corresponding numbered terminal on the new switch. Be sure to put the mounting plate on the stem. Place the new switch in the cover plate and insert screws. Put cover over switches and insert the three screws on each side. Turn breaker on and turn burner switch on. Success!

1. Moved stove from against the wall. 2. Unplugged the power supply. 3. Removed the electrical pannel cover. 4. Disconnected the quick connect probe plug. 5. Opened the oven and removed the probe. 6. Installed the new probe. 7. Connected the quick connect plug. 8. Reattached the electrical panel cover. 9. Plugged in the electrical supply. 10. Moved the stove back into its original position. ****Note**** THIS IS THE SECOND TIME I REPLACED THE PROBE. THE FIRST REPLACEMENT LASTED ONLY 5 MONTHS!!!!

watched a U-Tube video on this subject.....worked like aa charm!!

Lay gasket across opening after you have cleaned out the crumbs and old gasket. with your left hand spread the opening and gently push the new gasket in, make sure the edges go down and under the cooktop and the panel where the knobs sit. It should be smooth and slant towards the cooktop.

Took door apart, went online to partselect, ordered new glass, and put it back together. Oven looks like new. Makes sense to order the isolation as well when you do the repair

with a schematic of the door, this was fairly easy. since we had to take it completely apart, we cleaned the glass as well and every little nook and cranny. Once we put it back together, the door looked like we just bought it. these days, with whats available online, scary jobs turn out to easy.

I unplugged the stove. Then I lifted up the top of the stove to expose the burners. I unscrewed the necessary screws and plugs that attached the old burner to the stove. Then I simply put the new one back in it's place. The stove was one of those flat burner stoves, and I was a little concerned that I would be able to do it. The repair man wanted to charge me $150.00 for labor.

simple, removed a few screw's, unplugged old burner, plugged in the new one. that was basically it. easy!