79096544600 Kenmore Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- George from JACKSON, MI
- Parts Used:
- 316400601
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Had aluminum foil stuck on bottom
Removed 2 screws, pulled out the panel, replaced the new panel and replaced the two screws. Less than 5 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kathy from Greentown, PA
- Parts Used:
- 316490001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
oven temp was not right
We removed the old part and replaced it then when warming the oven all of a sudden there was a loud noise and something went and so we called a repair man which I guess we should of done in the first place. Now he has ordered a part that cost 170 soo that is my story don't try to repair if you don't have experience.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from Falmouth, MA
- Parts Used:
- 5304409888
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Wrench set
Oven wires arced and caused the terminal block to melt and become detached from the back of the range
Removed the wires that I could, then terminal block. Installing the new terminal block was very easy; however the wires that arced were fused to the terminal bock screws and needed to be cut and new connectors had to be put on the wires to allow them to be reattached to the block safely.
Once all was replaced and reinstalled the oven has worked great. The length of the repair was increased because of the melted parts and having to run to the store to get the new wire connectors big enough to fit on the wires. If we were simply replacing the block and had not encountered the melted ends, it would have been a very quick and easy repair.
Once all was replaced and reinstalled the oven has worked great. The length of the repair was increased because of the melted parts and having to run to the store to get the new wire connectors big enough to fit on the wires. If we were simply replacing the block and had not encountered the melted ends, it would have been a very quick and easy repair.
Was this instruction helpful to you?
Thank you for voting!
my burners would just heat up solid red even when i had controls turned down to 2 or 3. i would have to turn controls off and back on, then they still would just go back to glowing red
This was my first time ever working with electrical issues. My husband is not physically able to do repairs now. Very easy fix. Just viewed video repair instructions and it went exactly as instructed. Within 45 minutes, I had my stove repaired and cleaned and back in working order!! Great results. My range is working perfectly again and Mama is happy!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dante from SOUTHOLD, NY
- Parts Used:
- 316436000
- Difficulty Level:
- Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Right rear burner not working properly
After a brief discussion with CS about the electric stove part was shipped it arrived and I proceeded to install I found it needed to be installed sideways not up & down like the old one. The terminals did not line up so I put the black lead first and the purple lead last in doing that I burned out the switch??? was not easy to install as the video showed his switch matched each wire? My installation was sideways??
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Richmond, IN
- Parts Used:
- 5304503232
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Crack in inner door glass
Removed two screws that are attached to handle then removed four screws from bottom edge of oven door. I was then able to remove the outer door glass,this gave me access to the three inner glasses. After removing the retainer for the glass assembly,I was able to remove all three and replace the inner one.I reversed this proceedure to reassemble.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from Ozone Park, NY
- Parts Used:
- 5304503232
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Change on e of the inside glass
removed the screws holding the front part of the door and from there worked my way, untill the third glass.
It took a couple hours, my first time,. Overall easy,
It took a couple hours, my first time,. Overall easy,
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from COZAD, NE
- Parts Used:
- 5304524341
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Lens cover for the oven light
Very easy just had to pull the wire up that holds it secure.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- junius from WICOMICO, VA
- Parts Used:
- 316436000
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver
Burner switch work sometime.
I follow the video on your site
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dineshbhai from Rincon HWY21, GA
- Parts Used:
- 316436001
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
N/A
I had open back cover and remove the switch than replace new switch. Makesure cable conection.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from TULSA, OK
- Parts Used:
- 316203301
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Broiler element fried, found nothing in town, Part Select delivered in three days
Pulled oven out, took the screws out of back plate cover plate with socket wrench, pulled connectors out through the back, removed the door, pushed the element rods through the two holes, connected the two wires, screwed the element in, put the hangars on for the element, put the back plate on and turned the broiler on, worked great, put the range door back on and has been working great. Great company, hope not to use them again, but good to know they are there with my part.
Gary H.
Gary H.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Novi, MI
- Parts Used:
- 5304533520
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set
The out side ring of the element was working. The middle portion was dead.
I watch you tube of how to repair to gain my confidence and attempted the project. It was fairly easy. I took photos of wires so I wouldn’t make any mistakes. Boom ! Finished and works like a charm!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from BENTON, IL
- Parts Used:
- 316238201
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
The range element was not coming on
After settling that it was the Surface Element Switch, ordering and securing the switch, the first step was to disconnect the power to the Oven/Range. Next pull out the Range and remove the back and disconnect the switch from the top of the Range. Using the new switch I removed the wire connectors from the old switch and reconnected them to the new switch in the same spot that they came from. After connections were secure I reattached the switch to the back of the Range and reattached the back of the Range. When everything was back in place the power source was reconnected and that was it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jerome from WOOD LAKE, MN
- Parts Used:
- 316203301
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
NO HEAT IN UPPER ELEMENT
NEED A QUARTER INCH SOCKET FOR THE BOLTS. REMOVE THE BACK PANEL AND THEN YOU WILL SEE THE TWO ELECTRIC WIRES GOING TO THE TERMINALS OF THE ELEMENT. DISCONNECT AND THEN GO TO THE FRONT OF OVEN AND REMOVE THE FOUR BOLTS THAT HOLD IN THE TOP ELEMENT. SIMPLY, VERY SLOWLY PULL THE ELEMENT FORWARD UNTILL IT CLEARS THE BACK AND YOUR GOOD TO GO. DO NOT FORGET TO DISCONNECT THE POWER TO THE OVEN BEFORE YOU START!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ron from CINCINNATI, OH
- Parts Used:
- 316400601
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven bottom panel rusted away
Removed two screws removed and replaced panel.
Was this instruction helpful to you?
Thank you for voting!