79070301701 Kenmore Range - Instructions

Got a copy of the parts breakdown for the oven door from partselect. Com. Removed 8 screws from outer frame (3 top, 3 bottom, 1 on eah side). Removed the main glass pane from oven door, be careful when doing this as this is most of the weight of the door. It will want close on its own due to lack of weight. Removed the 2 top screws that attach the handle. Removed some screws from some plates that retain the 2 panes of glass of glass. Removed the third (most inner, broken) pane of glass. Replaced with new one. Reversed disassebly procedure for assembly.

There were only 2 screws that held the door handle & cap in place, removed screws & handle to get cap pieces off. Ordered new cap, - lost screws - cap delivered - no screws had to order screws, damn! They're expensive too !! Got screws, installed handle & cap, now wife is happy again!

Very simple. Removed oven rack that had melted residue on it and replaced it with the new one from your company. I want to tell you that the delivery service I received was just geat. Took less than 48 hours to arrive at my home from the time I placed the order on line. Keep up the good work and I will be happy to share my experience with those in need of you services. Thanks. Marilyn Kasson

Pulled out broiler drawer, removed 3 bolts, plugged in new igniter. Only issue was one of the tiny bolts stripped, so now only have 2 holding it in place.

New ones fit perfectly. Take a minute to bend the frame straight. Then and I used oversize screws on the replacement parts as the drop had stripped out the screw holes of the frame.

removed racking, flame cover, and wire plug in cover by pulling out racking, removing one nut, and one screw for the cover. Removed two small bolts to remove igniter, and then unplugged from two locations. Did the same in reverse for install.

Partselect always have their install video with the parts they sell so it was easy. I know contractors must not be happy with people like partselect and YouTube with all the instructional videos they supply us with. Keep up the great work partselect.

I loosened two screws(one on the left and one on the right) at the inside base of the oven door, then lifting the door off. The hinges are held in place by two screws and a flat metal covering. Remove the faulty hinges. The screw holes on the new hinges have to have some WD40 applied and then screw the screws in and out to widen the holes a bit. Once the screw goes in easily, remove them and insert the hinge into the hole that you removed the old hinges from. Replace the metal covering and insert the screws. tighten the screws. Open the hinges then slip the door back onto the hinges. Reinsert the two screws at the bottom of the door and tighten. I recommend replacing both hinges as there is a plastic insert in the hinge that becomes brittle over time and breaks.

I put in the part and it went well, I have used other parts from your factory for the same stove so I knew it was going to go easy. The part only required one screw.

First, I read about the experiences of others who did this repair.

Then I removed the oven door by removing the single screw at each hinge - visible when the door is open - using a #2 Phillips screwdriver (the only tool needed for this repair). I placed the door on the kitchen table and removed the two screws at the inside top of the door - they also hold the handle onto the door.

I placed the four screws removed from the inside corners of the door -- into one corner of a tray I used to hold the parts in order. Then I removed the eight screws from the perimeter of the door and placed them into another corner of the holding tray. Then I turned the door over and removed the outside part of the door from the inside - as in removing the cover from a box.

Then I removed four screws holding the middle and outside glass panels and placed them in another corner of the parts tray. Then I removed two screws holding the steel panel against the glass. Then I removed the broken glass from the bottom of the tray. That's when I discovered I had ordered the wrong glass panel.

I called the PartSelect number to return the glass, and while discussing how to return the part, I asked if I had to call another number to get the correct part. The lady assured me she could process my order for the correct part. She was very knowledgable about the system and quickly found the correct part from the schematic. I received the replacement part 24 hours later and installed it within 20 minutes.

Overall a success story. Excellent service and easy work.

I removed the oven door using a phillips screwdriver. It was very easy because I didn't have to worry about the door hinges springing the door back. I'm not really handy and it went very easy.

Disassembled inside of oven. Slid away from wall opened back replaced safety valve and igniter. Safety valve was good changed only because it was apart. Resemble and test sat. Kept old safety valve for emergency spare.

I did the repair with the instructions from parts select
It was very self explationatry
Thank you parts select
I saved at least $400.

remove oven floor and racks remove two self tapping screws unplug igniter replace be careful not to touch element plug in reverse order to reassemble

Once I recieved the new part it was easy to determine what two screws to remove to remove both the panel and the handle. I removed the two screws, slid the panel up and removed it. The new panel locked into place when slid down over the door and I replaced the sctews.