79094224403 Kenmore Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Conan from Moline, IL
- Parts Used:
- 5303935058
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
Two burners did not heat
Pretty easy installation; you lift the top plate up and snip the wires maybe four inches away from the burner. Leave more wire than you think you need; once you get into it you'll realize you need more wire length than you think.
Then strip the remaining ends, twist them together with the provided caps, and use the heat shrink to hold it together. Remove the old terminal, replace it with the new ones, and you're good to go!
Remember to check that the wires are tight in the cap before heat shrinking, though. I had to get more shrink wrap in order to finish.
Then strip the remaining ends, twist them together with the provided caps, and use the heat shrink to hold it together. Remove the old terminal, replace it with the new ones, and you're good to go!
Remember to check that the wires are tight in the cap before heat shrinking, though. I had to get more shrink wrap in order to finish.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Margaret from Spencer, OH
- Parts Used:
- 316442301
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
8" stove top element would not warm up.
It was simple.............the range-top tilts up so I proped it with a stick of wood, pulled out the old burner and plugged in the new one (when I saw how inexpensive the new element was I orderd two to replace the other 8" because it didn't look long for this world either). The whole operation took less than 10 min. no tools or batteries required!!!!!!!!!.........no-mus-no -fus.
Your prices were the lowest I found on-line, keep up the great work!!!!!!!!!
Your prices were the lowest I found on-line, keep up the great work!!!!!!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Danny L from CHELAN, WA
- Parts Used:
- 316442301
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Heavy jam boiler caused elements to sag
Removed the old & simply inserted the new one
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barry from MENDON, NY
- Parts Used:
- 316400601
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bottom panel burned through
Remove two back knurled screws, lift out old bottom, screw in new bottom panel. Removal of oven door (two flip out handles at hinge( makes this a little easier. Our oven did not need any other dis-assembly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kathryn from LAKELAND, FL
- Parts Used:
- 316400601
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bottom oven pan was warped and discolored
Unscrew the 2 screws at the back of the oven bottom pan in the range. Place new oven pan in and rescrew the 2 screws. I could not get the two screws screwed back in. Since the bottom pan cannot move from its position, I felt like the two screws were not necessary.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donna from UNION, OR
- Parts Used:
- 5303935058
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
replaced terminal block for element
followed the video provided on line which was very helpful..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chuck from EVANSVILLE, IN
- Parts Used:
- 5303935058
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Terminal block was bad.
Cut the old block off tied new wires to hot wires . That easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from HAYDEN, AL
- Parts Used:
- 316442301
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Cooktop burner was wore out from age
Just pulled the old cook top burner out and put the new one in .it took about 1 1/2 minutes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from PRAIRIEVILLE, LA
- Parts Used:
- 5303935058
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Original terminal degraded and faulty
Turn off power, remove heat coil assembly and drip pan. Unscrew the terminal assembly from the range top. Cut back 3 inches on each terminal wire and strip insulation 3/8 inch. Terminal assembly should be with the short side of the black block (from the side securement hubs) facing toward the coil stems. Slide the shrink wrap onto each wire and Twist each old with each new wire using the wire nuts and slide the shrink wrap Over each. Using a hair dryer, heat gun, or open flame carefully shrink the wrap. Secure the terminal back in place on the range.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rhonda from PACHECO, CA
- Parts Used:
- 316404002
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
wrong part received and returned
I wanted the bracket for the oven heating element and received the bracket for the broiler.... part returned and now I am stumped about what my next move will be
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from New Castle, PA
- Parts Used:
- 318372211
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
Burner element failed
Plugged the new one in and it worked.
I did search out Frigidaire parts and there are other types tha may or may not work. Calrod burners are not all that unusual. I went with the real thing.
I did search out Frigidaire parts and there are other types tha may or may not work. Calrod burners are not all that unusual. I went with the real thing.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from TULSA, OK
- Parts Used:
- 316203301
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Broiler element fried, found nothing in town, Part Select delivered in three days
Pulled oven out, took the screws out of back plate cover plate with socket wrench, pulled connectors out through the back, removed the door, pushed the element rods through the two holes, connected the two wires, screwed the element in, put the hangars on for the element, put the back plate on and turned the broiler on, worked great, put the range door back on and has been working great. Great company, hope not to use them again, but good to know they are there with my part.
Gary H.
Gary H.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jerome from WOOD LAKE, MN
- Parts Used:
- 316203301
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
NO HEAT IN UPPER ELEMENT
NEED A QUARTER INCH SOCKET FOR THE BOLTS. REMOVE THE BACK PANEL AND THEN YOU WILL SEE THE TWO ELECTRIC WIRES GOING TO THE TERMINALS OF THE ELEMENT. DISCONNECT AND THEN GO TO THE FRONT OF OVEN AND REMOVE THE FOUR BOLTS THAT HOLD IN THE TOP ELEMENT. SIMPLY, VERY SLOWLY PULL THE ELEMENT FORWARD UNTILL IT CLEARS THE BACK AND YOUR GOOD TO GO. DO NOT FORGET TO DISCONNECT THE POWER TO THE OVEN BEFORE YOU START!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jan from Storm Lake, IA
- Parts Used:
- 316442301
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
dead burner
I unplugged the dead burner and plugged in the new burner. Very easy. No tools needed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Elizabeth City, NC
- Parts Used:
- 316442301
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
burner was damaged
snap out the old one and snap in the new
Was this instruction helpful to you?
Thank you for voting!