79070112705 Kenmore Range - Instructions

Removed the old oven racks and put in the new ones.

1. Removed original knob from dog. 2. Ordered replacement knob. 3. 3. Replacement knob was delivered. 4. Replacement knob was pressed over the control shaft to the range's gas valve. Done.

We recently purchased condo and WhiteWestinghouse range needed some love. the old racks were not in very good shape so we ordered new.

Replaced temp probe and checked OK. This model did not have a full back as the instructional video showed. No cover to remove at all. Only suggestion might be to include two wire nuts of proper size. Average wire nut would be too big. Fortunately, I happened to have a couple.

I just installed the extra rack and re-arranged the existing ones. Works great!

I pulled the top cover from inside the oven off and unscrewed 2 screws to remove the heat plate. After i unplugged the adapter for the old ignitor apart and unplugged 2 wires and removed 2 screws that hole the ignitor to the plate. i replaced with the new ignitor, screwed back in place , plugged the 2 wires and the adaptor plug in and i was done , in less that 30 mins.. I also saved $180 (Sears $260) on this do it yourself repair.. Thanks PartSelect for having the part in stock.... R Diaz (Bklyn N.Y.)

The foul order was the cause of a "Mummified Rat" that I found on the bottom Left /outside wall of the oven. I first Unplugged the stove and turned off the gas. I removed the grates and the burners. Each burner is held down with two (2) 3/16" screws which makes it a total of eight (8) screws in all. After removing all eight screws, you can now pop up the burner lid with a putty knife or a large Screw Driver. I used a large screw driver, After removing the "Lid" you will then see the "Insulation Blanket" draped over the oven, to remove this blanket there are two (2) copper wires securing the blanket in place, you'll have to cut these in order to install your New Blanket. Removing the "Blanket " is a "No Brainer" just be cautious and don't snag any of the "Igniter Wires" The "Insulation Blanket" goes on one way, this can be identified by the pre-cuts on the blanket. I started out on the left side of the stove, and had the right side of the "Blanket rolled up. As I tucked the "Blanket" under the "igniter Wires" and slowly and gently feeding it with my left hand till it lines up with the pre-cut and drapes itself into place as you maneuver it down with your hands Now start with the right side by unrolling the "Blanket" and following the same procedure making sure the "Insulation Blanket" is fully extended on both sides of the oven.

Did just want to comment on the customer service. It was great. The easiest to order that I have ever dealt with. Received prompt attention to the order and processing the same. JUST GREAT> Thanks

1. Remove the old Trim by opening the door and unscrewing the two top screws holding the trim and glass to the door. 2. Lift the trim piece off of the glass, being careful as the glass will be a bit loose, and unscrew the handle from the trim piece, discard those two screws. 3. Place the new trim piece on the glass so that it fits snugly. 4. Place the screws back through the holes on the inside of the door, through the new trim piece and attach them to the handle. 5. Tighten down snugly and close door. You are done!

I checked the internet and found PartSelect.com the most affordable (lowest price) for the part. I got the part within 3 days which was very quick. Replacing was unscrew and re-screw at two points. it took me about 15 minutes (including opening the box and talking to my wife on the phone for 5 minutes).

The gasket just snapped in place. The first one I ordered was, my fault, the wrong one and I returned it and got the correct one two days later.

Very easy--just had to drill new holes for the clips because the are already pre set in the rubber gasket

We took off all of the bolts holding the burner assembly's in place . Then took the top of the s range off. Used a wrench to remove the old assembly and re-placed it with the new one. It took longer to get all of the top and under cover off then to put the new part in. Very good service from Part Select. MATT

Would have been simple if Frigidare had not changed the plastic snap wire connector on the part. The replacement part had a different snap together wire connection. After a couple of phone calls stating that the new part and the old part had different part numbers was informed that you have to snip off the ends and use wire connects but it was the right part. Once I knew that it was a simple repair if you have the wire connects to connect the wires.

Unplug the stove from the wall socket. Remove the oven door as shown in the instructions for replacing the door. This makes the job a lot easier. At the rear of the bottom panel there is a screw at each corner. Remove these screws, a screwdriver will loosen them, then remove by hand. If you have a convection oven remove the fan cover as this prevents the bottom panel from coming out. There is a screw at the top and the bottom of the cover. You can then gently lift the bottom panel at the rear and work it out of the front lip. Install the new bottom panel in reverse order.