79070402011 Kenmore Range - Instructions

First of all I would like to comment on how it easy it was to place this order and I was pleasantly surprised that it was rec'd the next day. Also it was the correct part that I needed. To install it, first I removed the screws and then the metal that was holding the broken glass. Once the broken glass was removed, I set the new glass in the metal strips and basically screwed it back together. Please note to be careful to remember which screws go where as they are not the same size and do not fit anywhere but where they belong. That was the only part of the job that I had a problem with.

The repair went relatively easy especially after reading that another homeowner found the door to be "spring loaded". I was prepared and made sure I held onto things tightly.I removed the screws as I came to them and carefully removed the other 3 pieces of glass, finally reaching the inner panel. Putting that in and holding it as I put the next piece back was the most difficult. Once that was in place, the rest was just a matter of redoing what I undid. Needless to say, I was a bit nervous the first time I used the oven. No problems though, works like a charm! Thanks!

I replaced the bulb using my hands to twist the bulb in the socket located at the top of the refrigerator.

I couldn't unscrew the leveling foot because it was rusted and corroded. The bracket holding it was easy to remove so I took the bracket with the corroded foot off and replaced it with the new foot and bracket. Very simple. I made sure I oiled it so it wouldn't rust again.

I took the brads that were left from the old gasket off with needle nose pliers. Then I put the new one on. It was very easy.

It went very well. Very quick. Just took out a couple of screws, took out the rest of the broken glass, slipped the new piece in and screwed it all back together. This was the first time I had ever tried to fix any part of a range/oven before, it was very simple...

It was a replace racks not repair. No problem

Unplug the range, remove racks. Remove 2 screws from the bottom back corners ( this was the hardest part. I used a stubby screwdriver, but a longer one would be better. They are fairly long screws). Remove oven bottom, lifting from the rear. Remove burner cover. Bottom left corner is a triangle cover. Remove this too. Remove the 2 screws holding the old igniter in place. The igniter unplugs easily. ( I used pliers, the plug has a clip, and pliers grip better.) Install new igniter ( it only fits in one way ) reinstall mounting screws and covers. Replace oven bottom. (I didn't replace the 2 screws. The bottom sits solidly, and they are a bit of a pain.) Plug in, set clock, test for oven to fire up.

The replacement racks were spot on and the service was outstanding. had the racks in 2 days. Happy Happy Joy Joy! :)

turn the gas off unplugged it form electric removed the line took the flame plate off removed burner tube and the screw out with a nut driver that was all just put it back in reverse

1. Unplug the range to ensure there is no electricity running through the range. The repair can be done with the propane/gas line still connected.

2. If possible, remove the storage drawer for ease of access.

3. Remove the screw from the metal plate in the left corner of the oven. Detach the end of the igniter cord that you find plugged in there.

4. Remove the two screws that hold the igniter in place. The old igniter should fall to the bottom of the range.

5. Take a picture of the two other cord connections that run into the middle of the back wall. This will come in handy for reference when you install the new igniter.

6. Route the longer extension of the new igniter cord through the hole in the metal corner plate, attach the cord, and put the screw back in to secure the corner plate.

7. Affix the new igniter to the same spot the old one had been in, using the two screws from step 4.

8. Plug in the two shorter cord extensions, using the photo from step 5 if necessary.

9. Reattach the drawer if necessary and plug the range back in.

10. Set the clock, then set the oven to a desired temperature to begin heating. If the repair was successful, the igniter will light the gas piped into the range, and you will see a ring of flame.

It went easy, I ordered the part from another vendor, received it in 3 days and it only took about 20 minutes to install.
I do not recommend ordering from PartSelect!

It’s a plug in part so other than working on your side while lying on the floor it was a snap. 20-25 mins.

It helps to remove the bottom drawer completely to gain easier access.

The bulb has a plastic clear cover. That cover can just be carefully removed using a screwdriver. It's held in by a metal bracket. After you remove the cover. You'll just need to replace the bulb and then re-install the cover and bracket.

Screw the handle, that it...