79092322300 Kenmore Range - Instructions

I used good old commom sense to disassemble and reassemble the frame, handle, internal glass,and inter panel to reach and repace the cracked glass. I must admit I had two machine screws left over during reassembly, but found a home. It is important to identify where each and every screw belongs. This will cut down your repair time. I thank PartSelect for providing great service and assisting me in my time of need.

Marv Dixon

It went easy, I ordered the part from another vendor, received it in 3 days and it only took about 20 minutes to install.
I do not recommend ordering from PartSelect!

Turn power off to the stove! Opened the oven door, removed 3 screws holding the top down. Lift the top up. (Take a picture first of where exactly the wires go and where the prongs go) I unplugged the 4 wires from the element. Use a screwdriver and pry the prongs through the metal brace. Remove the prongs from the old element because they are a separate part and don't come with a new element. If you wish to continue to use the stove, tape the ends of the wires up, because they will be hot when you turn any other burner on.

The bulb has a plastic clear cover. That cover can just be carefully removed using a screwdriver. It's held in by a metal bracket. After you remove the cover. You'll just need to replace the bulb and then re-install the cover and bracket.

I follow the video on your site

Very easy just had to pull the wire up that holds it secure.

First I removed the oven door from the range by removing 2 screws from the door. Next I removed 2 more screws from the oven door to get to the panel beneath. Once the top portion of the door was removed there were 4 nuts holding the glass sections together. Once these nuts were out I removed the broken class, replaced it with the new glass and reassembled. It was a very easy and quick project. I was so happy to find the part. I thought I was going to have to buy a new range. Thanks.

Got a copy of the parts breakdown for the oven door from partselect. Com. Removed 8 screws from outer frame (3 top, 3 bottom, 1 on eah side). Removed the main glass pane from oven door, be careful when doing this as this is most of the weight of the door. It will want close on its own due to lack of weight. Removed the 2 top screws that attach the handle. Removed some screws from some plates that retain the 2 panes of glass of glass. Removed the third (most inner, broken) pane of glass. Replaced with new one. Reversed disassebly procedure for assembly.

Very simple. Removed oven rack that had melted residue on it and replaced it with the new one from your company. I want to tell you that the delivery service I received was just geat. Took less than 48 hours to arrive at my home from the time I placed the order on line. Keep up the good work and I will be happy to share my experience with those in need of you services. Thanks. Marilyn Kasson

Assembled liner, panel and drawer. Installed the drawer guides and slid complete assembly in place.

I was forced to call in a pro repairman. Will cost me at least $150 for part and repairman. I could have done job if instructions on how to rewire had been included.

just put in slot

turned off breaker 3 Phil screws open door and on inside range top I would reconmend a board to hold top up square tip for cross bar and pliers to pull wires off fit perfect works really nice

Pulled oven out, took the screws out of back plate cover plate with socket wrench, pulled connectors out through the back, removed the door, pushed the element rods through the two holes, connected the two wires, screwed the element in, put the hangars on for the element, put the back plate on and turned the broiler on, worked great, put the range door back on and has been working great. Great company, hope not to use them again, but good to know they are there with my part.
Gary H.

Remove backing then unplug 2 wires and remove 2 screws, install new unit replace screws and backing plug it in all done less than 1/2 hour.