9117178610 Kenmore Range - Instructions

We follow the advise of one of you other viewers. It was so easy. Our thanks for the info and the speeding delivery

Good friend said he could do it no problem at all!!!!!

I removed the bottom drawer from the oven, took my handy nut driver out and removed two screws from the round igniter. When it was loose from the oven I removed the two wire nuts conecting it to the power sourse, I reversed the process and it was working again. One thing did go wrong my wife made me clean the oven that wasn't part of my plan :)

Using descriptions provided by others at this site, I replaced the old igniter with the new one very easily. Since this was the second time this oven has needed a new igniter, I did not need to cut the wires as described. Instead, I just disconnected the old igniter wires and rewired the new igniter wires. Replaced all the items I'd removed and the oven functions just fine.

Removed oven racks
Remove oven bottom
Remove 2 screws holding the glow coil onto the burner
Install the new glow coil with the furnished screws
Reinstalled the 2 wires back where you took them off

I took the old igniter out and replaced it with a new one.

removed screw from heat sheild, unpluged igniter and tested for 110v on wires feeding igniter (ok). removed bad igniter,ordered new one and installed with 2 - 1/4in. hex head screws. cut old male and female plug ends off old igniter, and wirenutted onto new igniter. turned on oven and it works fine. but noticed after oven burner lights, igniter stays on the whole time oven is on. I would think that it should go off when burner lites. Does anyone know if this is normal operation?

Replaced the old igniter with new one in 15 minutes. Popped the door off, took the bottom plate off, unscrewed the igniter and disconnected wires. Put the new igniter in and reversed the steps.....piece o'cake! Works great now!

simple remove & replace. 2 min job. Couldn't be happier.

The stories posted on your web page are great - only improvement would to add a schematic of the parts being removed - no issues were encountered - great service by the way - part arrived the next day - a Saturday!

John M.

To diagnos i removed the lower tray and could see the ignitor was not lighting like the broiler was,the same ignitor.I had the same problem as some of the other people so that was helpful.I removed bottom storage tray and could get to the wires and it was an easy fix,took about 40 minutes total.This website was very helpful also with excellent service on the parts and i saved a bunch of money!
Thanks,Gerald

First I got on line to make sure I had the right part. After it was delivered I started the project by unplugging the stove! A magnetic end for your socket device is very helpful.:-)A good alternative light source is esential to see what's going on.There is no need to pull out the stove.I then took off the oven door which is an easy process(Pull up off the hinges). I also removed the oven grates and lifted out the bottom plate which included the heat defuser.I then took out the storage drawer. The next step was to remove the rear screw and front 2 screws holding the burner tube. Then it was just a matter of pulling up on the tube and removing the screws holding the igniter.The 2 wires were then cut and the new igniter wires were spliced in with the new wire nuts that came with the package. I also used a little electrical tape to hold things in place. Then it was just a matter of replacing everything in reverse and plugging the stove back in. Everything works fine.

Per the instructions included with my part and from reading prior posts, I unplugged my range, removed my storage drawer, took the screws out of the bottom pan and removed. I found the igniter really easy to locate. As it was held in by a bracket that was soldered in, I found no need to remove many screws or to add the included mounting hardware as the part instructions suggested. I removed it, placed and mounted the new igniter (only two screws) before I snipped the connecting wires. Stripping the insulation material off of the wires seemed to be the MOST difficult part! I spliced the new to the old using ceramic caps enclosed with part, plugged in the range and fired it up...just to be sure it worked, and it did! I reversed the process to put it back together. Voila!

Removed the bottom cover plate and the bottom storage drawer. Disconnected the burner and removed it. Replaced the old igniter with the new one. The new one required the wire connectors from the old one to be spliced onto it. Reattached the ignitor to the burner and reinstalled the burner. Tested the new ignitor before reinstalling the cover plate and storage drawer.

I first read and printed out several postings on how others did the job. I read and re-read them and then I started. I cut power to stove and left gas on. I removed door, pushed back and removed bottom burner cover. I exposed the igniter which I deduced was the problem. I removed the front burner screw and the rear screws (2) and the burner came out very easy. I removed the igniter from the burner, made sure which wire went where (I marked them)an snipped them. I used the ceramic caps and spliced the wires. I replaced the burner and turned on the power. I turned the oven knob on and "Viola", the igniter came on and burner came to life. I replaced every thing in reverse order and called it "done". It was so easy with the postings on this subject.