66595779890 Kenmore Range - Instructions

My dual zone burner would trip my breaker anytime i tried to turn it on. All the other burners would work fine. I searched online and found a way to test my burner, which was shorted or grounded out. I purchased a new burner from the site...It was as cheap or cheaper than other sites. It showed up a few days quicker than i was expecting..I also replaced the switch to the burner, just as a precaution and to save time since i already had the top glass off of my burners....EASY JOB!

Loosen 2 screws and put new part in and tighten 2 screws. After putting in new sensor stove gave me another code had new part in 5 min and part select would not take my part back.

Followed instructions on urine that you provided. Instructions were great.
Only problem had was the screw was hard to get loose on one due to oven usage from previous people but I got it after a bit and then fairly simple from there. Unplugged and plugged new element in. Works although seems to run a bit hotter than before.

The old part, including lightbulb and socket, had corroded into place, and the glass light cover was stuck to the socket. I used a dead blow hammer and a dowel just under the diameter of the hole to tap on the back side of the socket to loosen it and get it out. The metal tabs on the old socket were folded back to make it fit better (?), which made it harder to remove. Lots of muscling of the part to get it out. Easy to install new part once old one was out of the way. An experienced person would have removed the old part and installed the new in no time.

Removed the ifinite controlswitch and replaced it but i dont believe it is wired correctly. now it wont get hot until it is set on four or so. think i the way it is wired.

Access to burner nothing like on-line videos:

1) Remove 4 screws under front control panel. (Oven door needs to be open.)
2) Remove 2 flat head screws on sides of control panel. This will loosen control panel. Capture control panel to keep from hanging from wires/connectors. I used hooks made from a wire hanger.
3) Remove 2 screws to remove two steel panels on either side of stove.
4) Remove rear screw of the 2 front screws now exposed and 2 rear screws near top of stove.
5) Carefully flip over glass top being careful not to pull on the wires.
6) Identify burner to be replaced. Note 2 numbers where two clamps are attached to burner.
7) Using 3/8” nut driver, remove screws to allow removal of burner. Remove wires per included instructions. Remove burner.
8) Place new burner under clamps and align to the holes by the two numbers noted in step 6 above.
9) Connect wires to new burner as per included instructions.
10) Reverse removal steps.

I found on youtube Also we marked each wire with masking tape 1A and 1B, 2A and 2B. The wires were the same color.

Went well. Husband, who has some appliance repair experience, did repair in less than a hour. Replacement burner was not an exact duplicate of original but he was able to adjust for that.

I installed the new switch. No difference. I switched elements with the other 8”. Same thing. I called Part Select and their rep said he doubted the new switch was defective but if it was they would replace it. But first how about trading the new switch with the other 8” switch that is working. I did that and the new switch worked fine on that burner but the old switch that worked before allowed the bad burner to go to red hot. Now I’m at a loss. All I see is a new stove. I don’t know what to do next and am open to any and all suggestions.

After my husband replace it we noticed that our knob was worn to the point it would not turn on the new switch. I am sure the switch was o.k. so kept the old one and getting a knob to fix the issue.

I used the replacement video from the web site. The replacement went great.

Followed the instructions in the video provided by PartSelect, which was very accurate. They only problem I have encountered is that the wiring from the old element compared to the new element do not match up 100%. I had to call Whirlpool today and schedule a Tech to come out and see if they can resolve the problem. Right now, when the burner is turned on, both the inner and outer elements turn on.

use needle nose pliers to disconnect the element from the power supply. After disconnecting it was easy to repair.

Took off oven door removed all screws to get old hinges out. Replaced with new hinges and put the door back together.

First I cut electric power off removed the two screws that hold glass top lifted up and removed two screws that hold element in place. I disonnected the wires and then pulled the element out