79046812992 Kenmore Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- James from MOBILE, AL
- Parts Used:
- 316217002
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
When oven was set at 400, actual temp would run about 285.
1 Turned off the oven breaker.
2. Removed the oven racks.
3. With a Phillips screwdriver, removed the mounting screws holding the temperature sensor and unplugged it.
4. New sensor plug did not match 20 year old connector. Had to cut and solder splice the connectors.
5. Installed the new sensor and now oven holds temperature steady.
Easy order, quick delivery and easy installation, happy wife.
2. Removed the oven racks.
3. With a Phillips screwdriver, removed the mounting screws holding the temperature sensor and unplugged it.
4. New sensor plug did not match 20 year old connector. Had to cut and solder splice the connectors.
5. Installed the new sensor and now oven holds temperature steady.
Easy order, quick delivery and easy installation, happy wife.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Earl from ALLIANCE, OH
- Parts Used:
- 316135702
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
Top burners were not lighting without a match
Was easy...I pulled oven out from the wall so I could get to the back.i used a nut driver to remove small silver cover.matched up wires to the never module and re installed.pluged oven back in and burners lit perfectly
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- christine from addison, PA
- Parts Used:
- 316217002
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
oven not reheating after initial heat up
unscrew the sensor inside the oven; took off the back of range to access harness of sensor; the replacement part harness did not match up to the original, so we stripped the clip from the end of the part and also the end of the harness in should clip into. after joining the wires together with ceramic wire nuts we tested the oven to make sure all worked AND IT DID!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Pearland, TX
- Parts Used:
- 318255006
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Element had burned out
Extremely easy. Two screws and electric connection that had easy pop on-off connection.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wayne from Palestine, IL
- Parts Used:
- 316135702
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
burner ingnighter would not lite burner
Replaced the ingintion module, still did not work, replaced the burner complete with new ingiter , it now works but another one quit . the front right one has 5 ohms resistance ,replaced with new one with 0 ohms, the back left has 2 ohms resistance and now it does not work , will need to replace that burner allso. too bad you can't buy just the spark module for the burner.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from Falmouth, MA
- Parts Used:
- 5304409888
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Wrench set
Oven wires arced and caused the terminal block to melt and become detached from the back of the range
Removed the wires that I could, then terminal block. Installing the new terminal block was very easy; however the wires that arced were fused to the terminal bock screws and needed to be cut and new connectors had to be put on the wires to allow them to be reattached to the block safely.
Once all was replaced and reinstalled the oven has worked great. The length of the repair was increased because of the melted parts and having to run to the store to get the new wire connectors big enough to fit on the wires. If we were simply replacing the block and had not encountered the melted ends, it would have been a very quick and easy repair.
Once all was replaced and reinstalled the oven has worked great. The length of the repair was increased because of the melted parts and having to run to the store to get the new wire connectors big enough to fit on the wires. If we were simply replacing the block and had not encountered the melted ends, it would have been a very quick and easy repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frank from CHESTERTOWN, NY
- Parts Used:
- 318255605
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
top electric burner not working
2 screws disconnected old one and pulled out the new one in put in opposite way. The representative was so helpful, part came fast. thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alan from SAN MATEO, CA
- Parts Used:
- 316538904
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Repaired Oven Range Light Bulb
The bulb has a plastic clear cover. That cover can just be carefully removed using a screwdriver. It's held in by a metal bracket. After you remove the cover. You'll just need to replace the bulb and then re-install the cover and bracket.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from WICKENBURG, AZ
- Parts Used:
- 5304409888
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- 30 - 60 mins
wrong part
my original part arrived and it did not fit. When I called to explain the problem I was told it was the wrong part. The big problem is... Frigidaire calls the receptacle a terminal block kit as well as a terminal block kit which is a totally different part. I tried to explain that to several different folks I spoke to at your company as well as Frigidaire but I'm not sure if I got that point across. Take a look at part # 530 393 5058 and part # 530 440 9888 and you will see that they both mention terminal block kit. Hopefully the part I am getting from Frigidaire is an OEM part and will fit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Oscar from Scranton, KS
- Parts Used:
- 316217002
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
F10 Error. Temp sensor at 1189 room temp ohms
1. Loosened 2 sensor mounting screws and removed them. 2. Tripped range circuit breaker to off. 3. Pulled out the range but left gas connected. 4. Loosened the 4 screws on RH side of the top back panel and carefully pried that side of the panel open. 5. Using fingers, threaded the sensor's wiring harness through insulation and into the oven. 6. Unplugged old probe. 7. plugged in new probe. 8. tugged wiring harness back through insulation behind the oven. 9. Using 2 screws removed in 1 above, mounted new sensor. 10. Repositioned top back panel and fastened it in place. 11. Shoved range back in. 12. Tripped range circuit breaker to on. 13. Reset clock. 14. Set oven to 450 for test tun. 15.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael A from Fairhaven, MA
- Parts Used:
- 318041603
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Replcement of inner door glass which had shattered
Removed the door from the range, disassembled the door, removed all broken glass fragments, installed the new glass, reassembled the door and reinstalled the door into the range. Straightforward and easy. Keep track of which screws go where and it is a breeze.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ashley from CARRIERE, MS
- Parts Used:
- 318255006
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Bake element in our drop-in oven stopped working
We turned off the power, took out the element, installed new element.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alan from ROCHESTER, NY
- Parts Used:
- 318255006
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Bake element was cracked
Remove the lower bake element by removing the 2 retaining screws that secure the element to the inside oven back. Carefully slide the element out. There are 2 wires attached to the terminals of the element. While removing be careful to not pull the insulation out with the wiring. Attach the wires to the terminals of the new element and reinstall in reverse order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Julia from NEW BADEN, IL
- Parts Used:
- 318255006
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Oven Bake Element caught fire
Unplug the oven (very important). Unscrew the bad element and screw in the new one. Plug oven back in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sheila from Dayton, OH
- Parts Used:
- 318255006
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Bake element burned out in my slide in range
Turn off circuit breaker
Open oven remove two oven racks
Position flash light
Remove two Phillips head screws that hold the element in place
Gently slide out element until you locate the two small wires
Gently Detach the two small wires from the back of the burned out element
Position the new element in the bottom of the oven and attach the two small wires to the back of the new element
Gently slide the element back in place and replace the two Phillips screws that hold the element in place
Make certain the new element is lying flat on the bottom of the oven
Replace the two oven racks
Turn on the circuit breakers and test the oven
Open oven remove two oven racks
Position flash light
Remove two Phillips head screws that hold the element in place
Gently slide out element until you locate the two small wires
Gently Detach the two small wires from the back of the burned out element
Position the new element in the bottom of the oven and attach the two small wires to the back of the new element
Gently slide the element back in place and replace the two Phillips screws that hold the element in place
Make certain the new element is lying flat on the bottom of the oven
Replace the two oven racks
Turn on the circuit breakers and test the oven
Was this instruction helpful to you?
Thank you for voting!