79095268991 Kenmore Range - Instructions

Removed the heating element to prevent possible fire while waiting on the parts. Three nut-driver screws removed the back cover. Removed each of four wires and attached to new burner switch, one-at-a-time to prevent any screwups with reconnecting the switch. Unscrewed the old switch, Screwed in the new switch to the front panel. Replaced the back panel and *poof*, good as new. Took as long to repair as it did to write this description.

the rear glides were missing on the back of the drawer so the drawer would pull out but when pulled back in, would tip down and not catch on anything. I ordered the parts then found an instructional youtube and watched it. Easy repair, cheap!

The drawer dropped down and would not easily open or shut or fit up good when closed. A quick inspection showed that one of the rear drawer guides was broken. The parts were ordered on a weekend and they showed up on Tuesday. We already had the pots and pans out of the drawer. It took about 10 minutes to put in the new guides (I replaced the one not broken also), clean and lubricate the drawer slides. Good as new. The repair video, although not necessary for this repair, was excellent. Thanks a bunch!

We removed the back of the stove, unscrewed switch from the stove face and unplugged the wires from the old switch. The new switch was universal so I had to follow the numbers by the prong on the old switch to determine which was the correct prong to plug the wires, plugged them in, screwed the switch back to the stove face and replaced the back Viola all fixed.

I am an electrician so I had no problem identifying wire and connecting them properly. However there were no instructions provided with the part and the configuration of the new switch was different than the the old one. I doubt if a DIY individual would have been capable of handling this task. Also there were no safety warning with respect to electrical repairs, which is a must today.

Took the back off and replaced the switch for that burner. Got alittle nervous because the switch did not look the same and the connectors were labeled differently, but it worked. Lost the red light button some how during the repair so when I turned the stove on sparks came out the back because the light connector was loose so I did have to order another one of those.

I got the ex husband to come over and take it apart and fix it, he said that it was a really easy repair to complete.

Replaced the control I got from you , even though it was a little different the lugs matched up and works great.

Screwed up by not shutting breaker. Shorted out 3 switches. Thought i could get away without shutting breaker that was a costly error. No problem replacing the 3 switches and element switch. Took about 1/2 an hour.Always shut breaker before doing any electrical repairs.

Cut the range power. Removed the top rear panel. Removed the two burner switch screws. Pulled one wire at a time off the old switch and put it on the new switch. Since the terminal location did not match, it was critical to notice the terminal designation on the old and match it to the new switch. Ex., H1 to H1; H2 to H2. Voila! It worked the first time.

watched the veido first then un pluged the stove then i took out 6 screws and 2 from the switch and reversed every thing

A Phillips screwdriver and pliers were all the tools required. At first glance, the physical appearances of the OEM and the replacement were not identical. The slide-on electrical tabs were numbered on each in the same way. Sliding off the connectors and re=connecting them on the same number tab on the new switch was all there was to it.

Replace the switch in the control panel. Had to take off the back of the range and remove the electrical conection and then pull the switch by unscrewing the screws that hold it into place. The n replacing the switch and then reconnecting the wires then testing. Worked fine.

The repair went really well, from the time I talked with the rep on the phone it was twenty four hours later and the part was in my hands. Great service! Because it was just the clock overlay all it took was a screwdriver to take the panel off and peel the old one off a nd stick the new one on. I will use part select again in the future.

if iever need to do this again i will unplug the stove and take the back off. iwill remove the spade connectors from the back and remove and replace the unit from the front. from the rear i will replace the spade connectors and the insulation . plug in the stove and make sure everything works. unplugthe stove, put on the back,plug in the stove and position it.