36291200102 Kenmore Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Jerry from Dallas, GA
- Parts Used:
- WB30X46987
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
bakinf element not working
best to pull stove out away from wall connect from behind stove
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mohammed from San Jose, CA
- Parts Used:
- WB17T10006
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
none to occasional power to burner elements
Exactly followed the instructional video and my installation was flawless. Now the burners power up and function like new. The whole repair was smooth and easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Franklin, TN
- Parts Used:
- WB30X46986
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
Element was burned out
Disconnected the plug from the receptacle; removed the 2 screws holding the element in place at the rear of the oven; removed the support bracket at the front (also 2 screws); removed the panel on the back of the range; pulled the wire clips off the element (had to replace one of them); slid the new element in place; reconnected the wires and fastened the element in place; reattached the support bracket and rear panel ... With the assistance of my wife (extra hands) this was an easy job!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from West Monroe, LA
- Parts Used:
- WB17T10006
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable)
plastic adapter was broken on end of the block kit
unplugged old block from both sides, ran new wire and plugged new wire to both ends and presto it worked, thanks for making it easy to fix. Thanks- Michael J Dumas
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- richard from Palm Coast, FL
- Parts Used:
- WB30X46986
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Socket set
Total Burn Out Of Original Broiler Element
Remove lower drawer and contents. Unplug unit. Tilt range on its back for easy access. Tie open oven door to forward legs with sturdy rope. Use small socket to remove 2 back screws and 2 forward element hanger screws. Detach broiler element connections from wire clips(2). Insert new element, attach 2 new connections to clips first. Install back socket screws. Install front socket screws for element hanger. Slide in oven shelves. Release oven door rope. Lift range to normal position. Replace lower drawer. Plug 220 in. Test oven element then broiler.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Fred from De Leon, TX
- Parts Used:
- WB17T10006
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Front and back burners not getting hot
Followed the video supplied with the email on the parts order form. Biggest problem was pulling the range out from the wall, the repairs went without a hitch. The PartsSelect video was a great help showing the short cut to getting the new wires in by using the old wires as a pull wire.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- don from protection, KS
- Parts Used:
- WB30X46987
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
element burnt out
ordered part shut electricity off took out 2 screws took of connectors put in new element replaced connectors replaced screws turn on elec started cooking
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Great Falls, MT
- Parts Used:
- WB50T10048
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Light burned out,couldn't see the clock.
Started off with a philips screw driver,and a cold beer.Removed the cover for the clock/timer. Removed the clock with a plain screw driver.Reversed the order of removal including another cold beer.Just think,I could become a repairman,with enough cold beer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Raymond from Highland, MI
- Parts Used:
- WB30X46986
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Socket set
broiler element burned completely out
Moved stove out away from wall .Unplugged stove, turned gas off. Unit is a dual fuel convection. Burners are gas, oven is electric. Removed 4 screws from back shield and exposed the 2 electrical leads connected to broiler element. Disconnected the electrical .Inside oven I removed the front bracket holding element in place, then removed the 2 1/4 screws in the back holding element in place. placed new element in and finger tightened the 2 screws, next I installed the front bracket and finger tightened those. I then snugged the rear screws in followed by the front. I went to the back and reconnected the 2 electrical leads. Replaced back shield and plugged unit in and turned gas back on.Caution; Make sure your gas line is flexible before moving your stove out to far. Repair was very easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from Port Gibson, MS
- Parts Used:
- WB30X46987
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Baking element burned out.
Turn off power to oven. Removed the rack. used a 1/4" nut driver and removed the two screws holding the element to back of oven. Slid the element out, unhook the two wires clipped to the end of the element. Replaced it with the new element, installing it in reverse. Took about 15 min. Rememer to turn off power to oven before attempting to work on it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Henry from Norwich, CT
- Parts Used:
- WB17T10006
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Burner not heating
Removed old socket, I had replaced with a aftermarket that really did not work well. When I recieved the terminal block kit from your company it was the proper kit. Service was better than expected, part and price was great and it took very little time ti install. Thank you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Rock Falls, IL
- Parts Used:
- WB30X46987
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
lower burner quit working.
easy, less then 15 min. but take off door first makes alot easier. and don't forget to unplug, like i did. just a few sparks but no damage thank god.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Maria T from Germantown, MD
- Parts Used:
- WB31T10010, WB30K10002
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Burned heating coil
Just pulled old coil out of the plug. Replaced drip bowl and inserted new coil in. No problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patricia from Centereach, NY
- Parts Used:
- WB31T10011, WB31T10010
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
needed new drip bowls for stovetop GE
removed the burners and dropped the drip bowls in. Very easy to do,
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Richmond, TX
- Parts Used:
- WB17T10006
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
GE Electric Range rear left burner quit coming on
Removed the back top cover with 1/4" nutdriver. Removed the burner terminal block with 1/4" nutdriver. Within 15 minutes had the terminal block kit removed and installed and in service.
Was this instruction helpful to you?
Thank you for voting!