36261121893 Kenmore Range - Instructions

The toughest part of the repair was the preparation to remove the old burners. As a result of the burning there was a carbon residue on the burners, on the gas outlet feed to the burners. This took some scrubbing and removing the carbon residue. Bits had burned onto the outlet and had to be scrapped off. Once all cleaned, replacing the burners was easy just had to place the balancing nuts in place and put on the burners. One problem arose the hood of the stove did not go back in place after replacing the burners so I then removed the balancing nuts put back on the burners stove top hood fit back in place and burners operated properly. This part of the repair took five minutes.

Removed old gasket and pried out clips with screwdriver. Installed new gasket.

Very easy! Open the top of the stove, remove the old double burner and place the new one! Anyone can do it! It's that easy... :)

Thanksgiving was coming and I needed extra oven space. So I ordered an additional rack. Installation ... just put it in the oven. My part came the day after I ordered it.

the flame spreader through the years, developed a hole above the glow coil causing the above trapped gas between the oven pan and spreader to ignite. by replacing the flame spreader the problem is gone and is now working properly. thank you, parts select for being there when i needed the part and also being reasonably priced. mike marino

Removed bottom shelf from inside oven, turned it obj and replaced the oven deflector with only a screwdriver

1st ensure thermostat is intact, I thought it was broken but upon further investigation I noticed that one of the screws that hold the thermostat in place had came loose which cause the thermostat knob not to be able to turn the thermostat stem. Re-installed thermostat mounting screw and it worked just fine.

ordered parts, 2 double burners, 3 days later they arrived.opened box.
lift stove top, lift out old burner,placed next to new burner to see if they were the same. THEY WERE. place in new burner, checked to see if burner assembly fit correctly. IT DID.
units purchased were exact replacements. supplied spacer nuts not needed.
easy fix looks new again, thanks.

Replaced old with new.

Lifted the top and dropped in the new burners. Realized they always should have had the leveling washers provided so I took the burners off, dropped on the leveling washers and dropped the burners back on. This all took about 2 minutes. Really made the range top look a lot nicer.

To: Remove.Four(4)nuts. Six(6)screws. Two (2) clips. To:Reinstall reverse process. "Very simple stright forward, and most enjoyable."

slid the old ones out and slid the new ones in. done

I removed the original gasket clips with pliers. I installed the new gasket by aligning the clips with the holes around the door and pressed into place. Easy fix!

I moved to an apartment where the past tenants did not take care of the stove. I think this stove is 10+ years old and looks like it was never cleaned in all of its existance! I cleaned everything really well with oven cleaner and lots of scrubbing. The stove looked brand new except the burners! I couldn't take it anymore so I ordered new ones. The burners came in less time than stated. I opened the box, took the burners out, lifted the oven hood and just placed them right where the others were. There are no tools needed it pretty much just gets placed down in the appropriate spot and that's that! No directions or tools needed. My stove looks awesome now!! When you first use the burners, you will probably need to place a match or lighter by the burner to get the fire going. After that, it lights perfectly every time.

The repair was somewhat easy, it would have been easiere if I had figured out the right part in the first place! Replacing the Thermostat is a simple task and actually only took abut 10 minutes. The harder task was replacing the glow bar in the broiler area! What a pain! The part had the same gender connector as the existing wiring. Had to cut the connectors off and use ceramic wire nuts... should be simple but the wires on the replacement part were about 1/2 inch too short! After some creative manuvering and about an hour of cussing out the OEM part manufacturer it went together and worked OK but I suggest before trying to solve a problem like this remember the basics... always check the obvious first!