790468130 Kenmore Range - Instructions

Took 6 screws out holding the top on from the sides. Lifted the top front, popped out the spark module, Took 6wires off & reversed the processed to install the new one. I was really amazed when I ordered it Wednesday and it arrived on Friday. Believe me I bookmarked this site.

Took 3 panels off to get to the electric block. Replaced electrical block and put it back together. Still no change.

Easy as 1-2-3

Removed 2 screws holding old temperature sensor inside the oven and gently pulled out the wire till the connector came through the hole. Disconnected old probe and attached new one. Fished the wire back in the hole and replaced the two screws. Then followed the operating instructions for calibrating the oven. Ended up setting it +5 degrees. So far, works great.

Took a screwdriver and removed screws attaching the element to the back of oven. Disconnectec the wires from the old bake element. Replaced the new reversing the process. Very easy.

First. shut off the power!!! Remove the two screws holding the coil. Next- slightly pull remaining wire to access the plugs. Unplug the wires, remove old coil, replace and plug in the new... Replace two screws.... Turn power on and....... Start cooking! EASY!

Used a screw driver to loosen 2 screws and the pulled the tabs off the old element and installed the new element. I am probably the most "unhandy " guy in the world but this was a snap. I am as surprised as anyone.

Moved the stove away from the wall, unhooked the electric cord and the gas pipe. In the oven, undid the two screws holding the probe. Removed two screws and removed the electrical cover panel from the stove back, disconnected the quick connect to the probe and pulled the probe from the oven. Reversding the proceedures, put the new probe into the oven, hooked up the quick connect and replaced the electrical panel cover. From the front, reinstalled the probe with the two screws, reconnected the gas and the power cord and put the stove back into position. It works just fine now!

The repair went relatively easy. I even cleaned all the layers of parts when they were removed from the glass panel. I have to thank the excellent customer service and super fast delivery. Overall a quite easy task and $$ saving as well!

1. Moved stove from against the wall. 2. Unplugged the power supply. 3. Removed the electrical pannel cover. 4. Disconnected the quick connect probe plug. 5. Opened the oven and removed the probe. 6. Installed the new probe. 7. Connected the quick connect plug. 8. Reattached the electrical panel cover. 9. Plugged in the electrical supply. 10. Moved the stove back into its original position. ****Note**** THIS IS THE SECOND TIME I REPLACED THE PROBE. THE FIRST REPLACEMENT LASTED ONLY 5 MONTHS!!!!

Square drive screws used throughout the oven since its manufactured in Canada. Shut power down to the range. Element fastener plate removed and 2 electrical terminals loosened. Used a pair of hemostats to hold on to the wires so as not to lose them to the interior back of the oven which was loaded with insulation. Connected the 2 wires to the new element, screwed the element fastening plate with element back to the back of the oven wall. Turned power back on and voila, I was back in business.

Started with three screws on outer edge of door, which separated inner and outer door parts exposing the first set of screws on first piece of glass. There are four panes including inner and outer with two between. Keep track of the screws, be careful removing and replacing glass panes (i put mat down to rest glass on)and with nothing more than a screwdriver and windex to remove fingerprints etc from replaced glass, it was a breeze. Good luck! - FK, Bahamas

We removed the screws holding the old element. Pulled the old element out of the back of the oven and disconnected the connecters (they just pull off). Slipped the connecters to the new element and pushed the element back in the oven wall and installed the screws. The only hard thing was removing the screws, because they had been in the oven for 15 years and were a little corroded.

watched a U-Tube video on this subject.....worked like aa charm!!

Gasket has pins that line up with tiny holes around the perimeter of door. Just pull the old gasket off, and snap new one ( with pins) in . Used the butter knife to push ends of gasket in hole at bottom of door. Took about 2 minutes to complete and looks AWESOME! simple. simple, simple! This company ships immediately and the product is described properly. I would buy from this company again!