3627526192 Kenmore Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
old burner pans that were burned by former owner
removed old pans, cleaned up stove, replace pans and now the stove looks brand new.
thanks part select for the great pricing and superfast shipment.
thanks part select for the great pricing and superfast shipment.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roger from Falls Church, VA
- Parts Used:
- WB48T10095
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
old blackened oven racks
Replaced old with new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carolyn from North Port, FL
- Parts Used:
- WB07K10232
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
The bottom strip had become rusty and looking badly
I pulled the oven door off the hinges and took the bolts out of the bottom of the over that were holding the strip on. I then pulled the strip off and replaced it with the new on. I replaced the bolts and then replaced the door on the hinges.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Todd from Falcon, CO
- Parts Used:
- WB13K21
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven would not ignite
First I removed the broiler from the bottom of the oven, then pulled the oven way from the wall to unplug it. I then removed the two screws that hold the igniter element in place. Ironically, the plug GE manufactures is reversed so i had to strip the plug and go end and reverse the wires to attach them to the oven. I used ceramic wire attachments as plastic would surely have melted. Replaced the screws, replaced the broilers, plugged it in, replaced against the wall and it fired up.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from Freehold, NJ
- Parts Used:
- WB13K25
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
Only one burner sparking on range.
Removed spark module only two small nuts. Inside was six wires on terminal. Removed one by one and connected right to the new module. Easy job 10 minutes and finished.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from TUCSON, AZ
- Parts Used:
- WB08T10026, 40A15
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set, Wrench set
Replace Oven light socket and light bulb in kitchen Range
1) Turn off power at circuit breaker panel
2) Slide out Range from wall
3) Unplug Range
4) Remove back panel and unplug electrical connections to socket
5) From front of oven, remove glass cover over old oven light bulb and remove flange that holds socket and bulb
6) Remove old socket from mounting flange and discard.
7) Place new socket into mounting flange
8) Screw mounting flange and new socket into the oven from front. Reattach electrical connections from back.
9) Screw in new light bulb from front
10) Replace existing glass cover over new light bulb and snap wire holder in place
11) Replace back panel
11) Plug in range
12) Slide range back to original position
13) Turn on power
Works like a charm! Thanks for having the parts after 30 years!
2) Slide out Range from wall
3) Unplug Range
4) Remove back panel and unplug electrical connections to socket
5) From front of oven, remove glass cover over old oven light bulb and remove flange that holds socket and bulb
6) Remove old socket from mounting flange and discard.
7) Place new socket into mounting flange
8) Screw mounting flange and new socket into the oven from front. Reattach electrical connections from back.
9) Screw in new light bulb from front
10) Replace existing glass cover over new light bulb and snap wire holder in place
11) Replace back panel
11) Plug in range
12) Slide range back to original position
13) Turn on power
Works like a charm! Thanks for having the parts after 30 years!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gerald from WINTERVILLE, GA
- Parts Used:
- 40A15
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
lights blown out
replaced lights in refrigirator and freezer
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles E from PINEWOOD, SC
- Parts Used:
- WB24K14
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
gas range and ignitor would not work on one burner
replaced ignitor switch between top burner knob and burner valve. Removed two screws from the top of the front panel and 4 screws from under side of front panel. removed panel and ignitor switch. slipped new switch on to valve stem reinstalled panel. ignitor works fine. You do not need to disconnect any gas lines to do this repair
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eugene from TUSCALOOSA, AL
- Parts Used:
- WB35X29720
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Oven door gasket was missing.
I removed the original gasket clips with pliers. I installed the new gasket by aligning the clips with the holes around the door and pressed into place. Easy fix!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Leroy-Anthony from Jamaica, NY
- Parts Used:
- WB20K8
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Oven ,Going on/off intermittently" Very Dangerous during day /at night especially when all is asleep /away from home,not knowing!
To: Remove.Four(4)nuts. Six(6)screws. Two (2) clips. To:Reinstall reverse process. "Very simple stright forward, and most enjoyable."
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Laughlin, NV
- Parts Used:
- WB48T10095
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
none
slid the old ones out and slid the new ones in. done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Willie from Shreveport, LA
- Parts Used:
- WB13K21
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Igniter went bad
1. Unplug from electrical outlet. 2. Turn off gas valve. 3. Remove oven door. 4. Remove bottom drawer. 5. Remove oven shelves. 6. Remove oven floor, take out the two screws at the rear. 7. Unplug the igniter from the wire harness, you can reach it from where you removed the drawer. 8. Remove the igniter, by unscrewing the two bolts using your nut driver. 9. Replace with new igniter. 10. Put everything back together, starting with # 9 and work your way to #1.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chris from Inglewood, CA
- Parts Used:
- WB13K21
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench set
Over not heating
1. Removed oven door..
2. Slide out floor plate of over.
3. Removed four screws securing the flame shield.
4. removed the two screws attaching the heating element to the burner.
5. Pulled heating element wires out of rear hole in oven and detached plug.
6. Attached new element and reassembled in reverse order.
2. Slide out floor plate of over.
3. Removed four screws securing the flame shield.
4. removed the two screws attaching the heating element to the burner.
5. Pulled heating element wires out of rear hole in oven and detached plug.
6. Attached new element and reassembled in reverse order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from Espanola, NM
- Parts Used:
- WB13K21
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Wrench set
Replace glowbar igniter
Removed the old glowbar's two screws. Didn't take a mental photo of its proper placcement (or a real one, which would've been smart). Removed screws holding 1) a heat protection plate, and 2) wire harness plate. Installed the new glowbar, hopefully, the right way - with its heat-plate facing the gasline of the over/broiler. Reinstalled the heat protection plate and wire harness plate. Hasn't blown up yet!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Erin from San Diego, CA
- Parts Used:
- WB13K21
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Oven wouldn't heat
I let my brother do the actual installation but it only look about 15 min. I did look at the website of the appliance manufacturer first and then came to this website. The cost of the part I needed was almost half as much as the other site. When I saw that someone with the same oven model number and had the same problem and was able to fix it, I decided to order here. It came quickly and my oven now works.
Was this instruction helpful to you?
Thank you for voting!