66575133300 Kenmore Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Richard from Wooster, OH
- Parts Used:
- WPW10181986
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Stove kept turning off
Looked up on-line the error problem and what part I needed to fix it. Part arrived very quickly and everything was going fine until I realized the stove had two sensors. Replaced the top sensor now I am getting an error on the bottom sensor. Maybe I replaced the wrong one. I will replace the bottom sensor with the one I took out and see if that does the trick. Very very satisfied with PartsSelect. Good Price, Quick Shipping, Would do business with them again. They are now in my favorites so I can find them again if I need parts.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Huntsville, AL
- Parts Used:
- WP8190282
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Broken and cracked drawer handle
Removed 2 holding screws in broken drawer handle and installed the new drawing in the reverse procedure
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Doris from Brookline, MA
- Parts Used:
- WPW10256908, WP3195097
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
When I originally purchased my stove, there was a large paper describing stove features. It was glued on and when I removed it, it left glue which I could not remove. I s hould have returned stove, but I didn't.
So, after several years of it bothering me, I decided to replace the oven panel. I ordered it one day and it arrived the very next day. It was an easy job to replace. Just remove two screws in back and replace the panel. While I was at it I also replaced the racks. Now I have a brand new oven,thanks to PartsSelect!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Grant from Alexandria, VA
- Parts Used:
- 8009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Light bulb failure
Received the part the day after ordering. Appreciated the quick service and repair took less than a minute.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Mauldin, SC
- Parts Used:
- WP8053334
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Rear drawer slide was broken.
Undid one screw. Removed the broken slide. Replaced with new slide an fastened with the existing screw. Problem solved.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Johnsburg, IL
- Parts Used:
- 8190618
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Oven would not ignite.
Removed the old burner and instlled the new one. It works great and I am a hero!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- dennis from tonganoxie, KS
- Parts Used:
- WPW10107820
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Oven Self Clean Would Not Function
Take off the back panel of stove and unplugged timer motor and switch on door latch assembly,removed two screws that hold assembly and slide rod off. I put 110 volt plug to timer motor and it did not move, that is how I diagnosed problem. Ordered new assembly (cannot buy just timer motor)put new door latch assembly on and worked fine. Of course unplug stove before you start !
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeff from Manhattan, KS
- Parts Used:
- WP8053334
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
broken rear drawer glides
just replaced the broken glides with the new ones.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brett from Arlington, WA
- Parts Used:
- WPW10293048
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench (Adjustable), Wrench set
Oven did not rise to temperature when at the bakie setting
First make sure it is the gas valve not the ignitor. If the clicking sound still happens then the ignitor is fine, no clicking means ignitor may be broke and try to fix that first because it is cheaper. For us I knew it was the valve because the ignitor still clicked and the broil and top elements still worked. After the part arrived I turned off the gas and pulled the power to the oven. Disassembled all the components taking pictures along the way to remember what it looked like to go back together. Installed the new valve and use yellow gas tephlon tape at the seals. Put components back in reverse order. Run the top elements first to get gas in all the gas lines and remove the air. At this point the oven bakes again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from Cornelius, NC
- Parts Used:
- WPW10181986
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
oven temperature did not stay as set
changing the part itself was easy, but the sheet metal covering the whole back of the oven was difficult to remove because of some screws that were stripped. The new sensor solved the problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from Ft Myers, FL
- Parts Used:
- WPW10118454, WP8523175
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Glass door front fell out during cleaning and shattered
Install bottom door trim first...Remove upper door handle and set new glass door front piece in place and re install upper door handle and tighten all screws...Looks great
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thaddeus from Washington, DC
- Parts Used:
- WPW10118454
- Difficulty Level:
- Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
broken outer range door glass
Using 4 strips of duct tape was useful,in holding the glass to the door.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- melody from springhill, FL
- Parts Used:
- WPW10118456
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Broke front glass of oven while moving
Looks better than the old one wes and so easy to do. Thanks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dave from Titusville, FL
- Parts Used:
- WPW10181986
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
E-2 F-3 codes..Oven inop w/trying to bake.Beeps @ start attempt.
Contrary to instructions(go thru front of oven) I had to pull out the range, remove two (2) screws from back chassis. At this point you pull out the connector, snap in new, reverse proceedure. Very simple. Hardest part is cleaning up debris generated by moving range.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wayne from Sykesville, MD
- Parts Used:
- WP3196262
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Replace oven door light switch
The replacement proceeds similarly as for electric range switch replacements described here, only this model is a gas range. The top panel does not lift up because of the feeds to the gas burners. It is possible, using a thin blade, to depress the spring fingers holding the switch in the oven panel, or else to remove it destructively. Be careful not to pull the old switch out too far, or else the wires will pull off the switch connectors and fall inside the oven-side panel cavity. This happened to me. The wires are very short. Another 1/2 inch of wire would have made all the difference. If this happens you have to fish out the loose wire. I gave up on this and took off the back panel (about 8 screws) and then loosened the bottom and sides of the side panel. This allowed me to retrieve the short wire and connect it to the back of the switch while pushing the switch into its mounting hole. Reattach the side panel, the back panel, and slide the stove back into place, and you should be good to go.
Was this instruction helpful to you?
Thank you for voting!