91191165690 Kenmore Range - Instructions

Watched youtube....

unscrewed it unhooked the wires and replaced with new part

What I had to do was open the slot for the burner pan more as it would not fit properly in. So we snip the burner pan a little and now it fits great.

I had grease on the baking element when I turned the oven on. I thought it would burn off, it caught fire and destroyed the baking element. I ordered a new element, it came within two days. I didn't wait for my husband to come home. I got a screw driver, took off the screw, used pliers to pull apart the old baking element from the wires. I did this carefully , our oven is old and the element was not pulling away easily. I inserted the new element, put the screws in and it worked perfectly! I was very proud of myself but the truth is that this is a simple job.

orderd a replacement part. recieved it two days later then that evening installed it. there was a video online to show how to replace it. very useful if your not a do it yourselfer.

I went on-line, found Partselect.com, they gave me the part number, showed me a video on the repair details, shipped the part overnight, and within ten minutes of the arrival of the part, I was up and running. EXCELLENT SERVICE! Thanks for saving Christmas at our house!!

You literally saved our Christmas from a disaster! Four days before Christmas our bake element gave out and we discovered it had split. We found you on the Internet, ordered the part, and prayed you would deliver as promised. We received it the next day, as promised, and in time to cook Christmas dinner. It was a snap to install, literally took five minutes. Your service, response time and instructions were perfect. Keep up the good work!

Piece of cake. 2 screws and a flashlight. I needed needle nose pliers to insert the "plugs" into the "sockets."

Removed to screws holding the bake element in place. pulled out element to get to the 2 electrical connectors. removed connectors from old unit. connected new unit and secured with the screwes. very simple.

I took out the two racks from inside the oven. I then took my cordless screw driver and unscrewed the two hex bolts from the back of the oven , where the element goes through the other side. Next I went to the back of the outside of the oven and unscrewed the two hex bolts that hold the gray guard on(It covers the wires). I unplugged the red and the yellow (might have been a white wire since it was dark back there). wires that connect to the element. I went to the front of the stove and took out the bad element. I took the new one and inserted it into the two holes from the old element. Plugged the red and yellow wires back up and replaced the guard. Lastly I screwed the element to the rear of the oven with the two hex bolts I used before.

first removed the two screws,pulled the element out ,disconnected the wires, pulled it out , cleaned the oven and then reversed the process. could not have been easier for a do it yourself homeowner on a budget.

The replacement element came within a couple of days of our order. From the time I saw it by the front door till the repair was complete was about 10 minutes. Half the time was taken in walking to my tool box. In just a few minutes we had tested the new element and were ready to make dinner. Great value for the price.

Cut power to oven from breaker box. Remove two retaining screws using a nutdriver at rear of oven. Slowly pull Bake Element from rear of range exposing connector clips. Disconnect at clips from oven wiring. Connect new Baking Element to wiring connectors. Push new baking element into rear of oven. Reconnect baking element using original screws with nutdriver at rear of oven. Turn on power to oven from breaker box. Job complete in 10-15 mins.

I removed the two screws with a nut driver, pulled the element out far enough to expose the connection point and disconnected the electrical clips. Upon receipt of the new element I did those things in reverse order and it worked great.

First I switched the fuse to the oven had no power and then I removed the old element and wiped down the inside with a damp towel.
I then attached the new element and then used the screws to attach the element firmly into place.
I then restored power by switching the fuse back and then burned the element to remove and chemicals and then done