36262780101 Kenmore Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Mary from Leon, KS
- Parts Used:
- WB17T10006
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Burner wouldnt heat
Watched video,and used it as guideline.Biggest problem was removing tape from old wires.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Hinesville, GA
- Parts Used:
- WB24T10027
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
burn out switches
Pull stove out from the wall unplug it remove the old switches and replaced them withe new one. they work just fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cory from Honesdale, PA
- Parts Used:
- WB24T10027
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Right front burner not getting hot
After searching the internet for a cause for the burner not getting hot it looked as though it was the burner switch. I ordered the switch and installed it. Behold it still did not work. I then ordered the burner, installed it and it worked. So I had a 50/50 chance as to which part was the problem. This was my first stove repair and I found it easy to do. Finding something to hold up the ceramic cooktop took the most time. I cut a piece of wood to prop it up while I replaced the burner.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Fuad from Sarsota, FL
- Parts Used:
- WB17T10006
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
2 mounting bracket included, wires too long
I couldn't tell which one work best till I installed 2 units and I liked the other bracket for stability.The wired were too long and there is not a given way to strap them and keep them away from the heat source.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jerry from Dallas, GA
- Parts Used:
- WB30X46987
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
bakinf element not working
best to pull stove out away from wall connect from behind stove
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Raymond from Highland, MI
- Parts Used:
- WB30X46986
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Socket set
broiler element burned completely out
Moved stove out away from wall .Unplugged stove, turned gas off. Unit is a dual fuel convection. Burners are gas, oven is electric. Removed 4 screws from back shield and exposed the 2 electrical leads connected to broiler element. Disconnected the electrical .Inside oven I removed the front bracket holding element in place, then removed the 2 1/4 screws in the back holding element in place. placed new element in and finger tightened the 2 screws, next I installed the front bracket and finger tightened those. I then snugged the rear screws in followed by the front. I went to the back and reconnected the 2 electrical leads. Replaced back shield and plugged unit in and turned gas back on.Caution; Make sure your gas line is flexible before moving your stove out to far. Repair was very easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sunny from Salt Lake City, UT
- Parts Used:
- WB31T10011, WB31T10010
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
stained drip bowls
unplugged burners replaced drip bowls plugged in burners
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Greg from Chicopee, MA
- Parts Used:
- WB30X46987
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Bake Element burnt out
watched the video on part select - took less time then they said.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Apache Junction, AZ
- Parts Used:
- WB31T10011, WB31T10010
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
old,burned pans
replaced
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Emily from Snoqualmie Pass, WA
- Parts Used:
- WB30X46986
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Broiler Element Replacement
There were two small screws at the back of the stove (this was the part that intimidated me. At first glance it doesn't look like it should be removed). But you just have to unscrew them, disconnect the wires behind them (this part can be done by hand), and pull the element out. The new element slides right in! Just make sure the power to the stove is disconnected either by breaker or by unplugging it. I'm not sure if it matters, but I made sure to connect the wires to the same side of the element that they were removed from.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stuart from Yelm, WA
- Parts Used:
- WB30X46987
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Heating element not working
Saw the brief video and as stated took less than five minutes to replace. It took longer to clean up the floor under the oven than to replace heating element.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- mary from morton, WA
- Parts Used:
- WB30X46987
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
burned out
replaced
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Rock Falls, IL
- Parts Used:
- WB30X46987
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
lower burner quit working.
easy, less then 15 min. but take off door first makes alot easier. and don't forget to unplug, like i did. just a few sparks but no damage thank god.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary Ann from Granby, CT
- Parts Used:
- WB02K10062
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Plastic glide broke
The person I spoke to knew exactly what I was trying to describe. The part arrived in 2 days. 5 minutes later the drawer was back in place. I was glad I save the screw as the part did not come with one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- GAIL from STREAMWOOD, IL
- Parts Used:
- WB31T10011, WB31T10010
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Needed new drip pans
Not really a repair. But would like to say, I like the price and shipping was super fast. Thanks.
Was this instruction helpful to you?
Thank you for voting!