36273429202 Kenmore Range - Instructions

Turned the wire protector to the side. Turned out the old bulb and replaced it with the new. Turned the wire protector back in place and I'm like new.

Ordered part from customer friendly Part Select and received the replacement part within a few days, and installed it promptly. Wife is happy and stopped grumbling about oven bottom unsightly defect! Small price to pay for a happy wife! Ernie

My husband and I probably could have done the repair in 15 minutes except for the difficulty lifting up the range top, dropping the screws into the range where they could not be retreived, threading the thermostate into the little holes from the top to the inside of the oven and then trying to hook the range top back into place. Even with all the difficulties we still accomplished the task in one hour. Thank goodness we had 4 extra screws that worked (actually only takes 2 but of the 6 we had, 4 fell into a place you could not reach into). Glue on the end of the screw driver finally kept the screws from falling into the black hole. It was an adventure and would do it again.

PULL RANGE OUT FROM WALL & ALSO REMOVED OVEN DOOR BY SLIDING UP. WORKING FROM INSIDE OVEN & ALSO BEHIND I REPLACED PART . ALWAYS " UNPLUG " RANGE BEFORE YOU START.

the electrodes on this model have to be removed before you can raise cooktop, once cooktop is raised remove wire from burner bracket, use needle nose pliers to squeeze bottom of clip,remove &replace with new parts.

This gas range had an oven that would heat, but it wouldn't hold it at a stable temperature. Say you set it at 300 degrees. Well, it'd head up to broiling temperatures, then drop down to like 200 degrees, then 400 degrees (You get the picture).

My guess was that the thermostat, given that this oven was ~20+ years old, was no longer able to detect correctly the temperature inside the oven.

The thermostat sensor is made up of the housing (The part that sits behind the oven temperature control knob), a long wire (so you can route it to the inside of the oven), and the probe itself (Which I boldly assume is the thing that measures the temperature inside the oven)

TL;DR:

-Pull oven from wall.
-Turn off electric and gas.
-Remove the grates and drip pans off the top.
-Pry the range's cooktop up (It's on like a hinge and is designed to lift up. You have to play with it a bit with like a screwdriver on the sides (One on each side). If you pry just a tad, you'll notice these prongs that act like detents. (LIFT CAREFULLY, the heating elements are still connected via their gas lines! They're flexible, but don't man handle the thing!
-Once that's up, it's time to finally start removing the thermostat which is the knob that controls the oven temperature. Pull the plastic knob off which will expose the two screws you need to detach it from the oven (Phillips head). Be super careful. You don't want to drop these screws. You'll be struggling to fish them out of the empty space that sits between the thermostat and plastic knob.
-Once that's loose, open the oven door and detach the thermostat from the back of the oven. Recycle the prongs holding the old thermostat sensor for the new one.
-Go to the back of the range. Like the actual back part of it.
-Frustrate yourself with pulling out the thermostat through the route it's been put in. It's difficult to route it through the tight spaces, but not complicated. Keep a mental note of this route and copy it with the new thermostat that you have to install.
-Don't fret, when it comes time to wire the new thermostat sensor, it's actually a lot easier than you would think to find that little hole in the back of the range that you have to slot it through. It's just slightly covered by insulation. Pulling it slightly aside, you'll see it very easily.
-Screw in the thermostat housing at the front of the oven.
-Frustrate yourself again by routing the wire while taking care not to bend the probe (This is my assumption not to bend it and I think it's a safe assumption to make)
-Find that tiny little hold in the back of the range again, insert the probe through it, then use those recycled prongs to hook that probe into place.
-Yay, you're almost done.
-Reinsert knob on thermostat.
-Turn gas and electricity back on.
-Give it a test run to see if you did it right.
-if it still doesn't work, then it might not have been the thermostat giving you problems.
-If it does work, put everything back the way it was.
-You're done.

Followed you tube instructions I found on line via parts select recommendations.

I put it in the same way tuck it out

Two set screws in rear; removed easily with a screwdriver. Old oven floor lifted out easily; new oven floor dropped in just as easily; set screws re-installed. Done. Pleasantly surprised at how easy this went.

Easy

I have no clue what wire goes where because there is no thing to refer to or instructions of any kind . I have not been able to install the part.

Start by removing all screws 3 for each burner total of 15 t-15 bit is required then proceed to remove spark igniters 5 total slight pull next step would be to slide a screwdriver under top left and right side to remove top shelf. There you will have access to the parts you need to replace. When done just reverse installation instructions to complete

Unplugged the range. Took out all the necessary screws and lifted up the cooktop cover. Unscrewed each gas tubes connecting to each gas burner's dial to allow more working space. Pulled out the old thermostat, installed the new one. Put back the gas tubes and all other necessary screws. Plugged the range and tested out the new thermostat.

Replaced the oven thermostat and calibrated the new thermostat by adjusting the temperature setting knob. Instruction I found on-line were very helpful and the repair was moderately difficult. Trickiest part was threading the new thermostat into the oven. Total repair time about 1 hour.

Followed the instructions I found on this site - it went really well - exception was trying to figure out exact slots for glass to fit in on top. Looks great!