91193614010 Kenmore Range - Instructions

Pulled the range out and unplugged it. Removed the back panel. Removed one wire at a time and plugging it in on the new switch. unscrewed the existing switch from the front panel (Two screws). Screwed the new one in, replaced the panel, plugged in the range and tested it. The new switch was a perfect OEM replacement and worked perfectly.

Pulled stove out and unplugged. At the rear of the range there were 4 faster. Used a nutdriver piece in an electric drill. Pulled off the cover and located the switch. At the front of the stove, I removed the knob and unscrewed two screws releasing the switch. I undid and replaced each wire connector one-by-one to avoid any wrong connections. Replaced and secured the switch and replace the back panel. All secured, power on and fixed! Easy repair, but something that had been put off for a year!
Also follow the installation videos from PartSelect - very helpful!

The repair was very easy and your video was extremely helpful. Especially regarding pulling the oven out and removing the back wiring cover to get to the spade terminals, rather than trying to do it all from inside the oven. Added bonus was that I got that pocket for the oven cleaned out like new! Eww! Pulling it out also gave me enough reach without having to remove the oven door (didn't realize you cold do that). Best part though was your mention that GE often DROPPED the zeros in their parts numbers. Couldn't locate the part on any website until yours noted this. so.. you got the sale. Went back to GE's website, located it and found your quality part was also less expensive! 11 minutes start to finish, quick shipping and works great! I'll be back! Thank you!

Took out the 2 screws,Pulled out the stove
Took the back off ,took the wires out of the little place where they fit in,Removed the old element.
Put the new one in Fitted the little thing which looked like a alumium flat piece back where we took the old one out.Put the back back on cut it on wheepe In business.Also the new element came here faster than I thought it would .I,m a 71 yearold grandmother.Pretty simple.

My stove would not heat. I could see that the bake element had a hole burned through it. Found this website. I was confused about what part I needed so I called the phone number and the girl was very good at locating exactly which element my stove needed after I gave her the stove make and model #. I ordered the part on Thursday afternoon. The part arrived on Saturday afternoon.

The hardest part of fixing it was finding the correct screw driver socket thingy (I'm not a technical person) to get the screws off with. Thankfully my neighbor had what I needed. I pulled my stove out from the wall (primarily because I needed to clean under there) and unplugged it. Unscrewed the screws, pulled the old element out until I could see the wire connections. I used clothes pins to hold the wires from going back into the stove once I unhooked them from the element (another tip I learned on this website) and simple slipped the wire connectors onto the new element, pushed it back into place, put the screws back on, plugged it in and TA DA... was baking a pizza in no time.

Very very VERY easy repair!!!

First I removed the two screws that hold the element in place. I then went to pull the element out and one of the wires touched the side of the access hole. There was a spark and the electrical breaker tripped. (Remember to always shut the electricity off first). Before I put the new element in I took off the access panel on the back of the range, slid in the new element, attached the two screwd that hold the element in place. Then I went around to the back of the range and re-connected the wires from that location to make sure there was nothing around the wires that would spark. Put the access plate back on and I was done.

Watched youtube video. Very easy to replace

I pulled out the old parts, dropped the burner bowl into place, then plugged the prongs of the surface element into their sprocket. It took about ten seconds and used no tools.

0) Take the back cover of the range off.
1) Carefully noted how the wires and the sockets were connected.
2) Visually checked that the new parts were practically identical old ones.
3) Put together the new sockets from the parts in the kit.
4) disconnect the old sockets and put the new sockets in place.
5) For each unit disconnect one old wire at the time and connect the new wire. Repeat the same for second wire.
6) Neatly bunch together the rest of the wires with electrical tape. Do not cut the wires!

That's it! It took about 20-30 minutes.

I first pulled the stove away from the wall to unplug and look from the rear. Look at the wiring from the back (you may have to remove 2 screws and the plate that covers the wiring) and take a picture of it if you can with your smart phone - this way when you go to put it back you have a reference. I then removed the oven racks and the 2 little bolts holding the element in place. Wiggle it toward you slowly so the wires don't pull off. It's easier if you use needle nose pliers to get the fittings off, if its hard wiggle the fitting it will come off. I put the connections on the new element and squeezed them tight not to move. I did put a small piece of electrical tape on the connection ends for my piece of mind. Screw it back in and, plug it in and turn on. If the element starts to glow your done, put the cover back on over the wires and slide it back in place. If your kind of handy you can do it.

Took off the ring burners and the old drip pans . installed the new drip pans and the old burners took less than 3 minutes...so easy

It took a bit of head scratching to remove the oven door. I had read another user saying he'd removed the hinge screws unneccessarily, so I left them alone. I eventually was able to locate the locks on each hinge. Once they were disengaged, it was a simple matter to lift off the door. After that, I removed all the screws (except the hinge screws) and took the door apart. Once it was disassembled, I found two loose triangular pieces, about 1 1/2" long. I later discovered these were spacers for the two top srews. They were placed on end, and the top screws passed through them. All in all, a relatively simple repair, which absolutely amazed my wife, landlord, faily, etc.

Unplugged the oven, took out old element and replaced with new element. It was really simple and easy to do, didn't even need my husband who is not mechanically inclined.

I got tired of trying to find the right parts in the stores and decided to order them. Finally I have the drip pans that fit my range!

Placing the order was very easy. Shipping was fast and excellent packaging. Thank you very much!