9117188811 Kenmore Range - Instructions

Followed suggestions of previous posts. Removed oven door, warming drawer, pan in bottom of oven. Removed element to replace igniter. One thing I would add is I put a small piece of electical tape on the heads of the two 1/4 in. screws for the rear element bracket. This kept them from falling out of nutdriver.

Diagnosed the problem as igniter failure and called local parts outlet. They gave me the part number, but said they were out and directed me to another vendor. When the part came, it was the wrong shape but I tried it anyway. Result - the igniter glowed which allowed the gas to flow, but igniter, being the WRONG PART, didn't ignite the gas, allowing a dangerous build-up of gas.

I then went to PartSelect, looked up the part, saw it was the correct one, ordered it (arrived within 3 days) and, because I already had the pans and covers off the oven, it was a matter of minutes to install. Works like a charm and, though I usually like to buy locally, I'll check out PartSelect first next time!

I removed the 2 screws that held the bottom oven plate in place. Then I removed the one screw holding the bottom burner in place in the front. I then reached into the rear area and unscrewed the last 2 screws securing the burner. I disconnected the igniter wires at their push-on connections and lifted the whole burner/igniter unit out. I relaced the igniter using the 2 attachment screws, and I cut the old igniter's wires with connectors and spliced them into the new igniter's wires, using the ceramic wire nuts that came with the new igniter. I reassembled the unit and it worked first time.

1. I have searched info on the internet and found that site.
2. Initially I could not figure out how to unscrew ingniter. After reading more post I have found out how to access nuts underneath.
3. After I have removed lower drawer and unscrewed metal cover and then inginter nuts.
4. I have got a part with two wires attached to the igniter and two porcelan insulator, so it was very easy to cut old wires and connect with an igniter wires in parallel

/||\
||

Checked on this website for ideas. A 20+ year repairman posted that the problem is the control valve and I should replace the igniter while I'm there. The valve was priced at $189 and the igniter $60. I decided to try the igniter first and all is well. Valve not needed.
Steps; remove; door, lower tray, and oven floor pan. Disconnect two igniter wires. Use 6mm sock to loosen gas feed tube, then lift tube up a couple of inches to access igniter screws. Remove them, and reverse process with new part. I tried to R&R the igniter without loosening the gas feed tube but it's a real PITA. Good luck, easy fix.

My repair was easy. The hardest part was trying to get the 2 small screws off and on the igniter. You need small hands or a small, angled socket set. I did mine with the door of my oven still on and maybe that was why I couldn't reach the screws that well. If you can do the repair with the door off, I would say that would be easier. As soon as the new piece was screwed in, it worked on the first try.

Ignitor is easily reached by removing the bottom of the oven floor. Machine screws remove easily when appliance is relatively new, but from experience, they may give you some trouble when stove is 5+ years old! Our part came in a timely fashion, even when ordered over a holiday weekend . Replace ignitor just as the old one came out-one word to the wise...scrape off enough silver coating on the wires so that a good contact is insured before splicing with the wing-nut included. Having had many GE stoves, I notice that the factory-installed ignitors have a shorter and shorter life; I'll be keeping PartSelect's website handy!

Replace igniter in oven. It was a simple repair and only required that I unplugged the power cord from the unit, remove the base and 2 screws holding the igniter.

I followed the other instructions folks had left, and things went very well. I did unscrew the mount to lift the entire flame assembly out, which made getting at the screws for the igniter much easier. Once I had done that, I clipped the wires close to the old igniter, one at a time, then connected them to the wires on the new igniter. The part came with ceramic wire nuts for this, which I was glad for because I wasn't clear how best to connect wires in a heated environment. Put everything back together and it worked perfectly.

Replaced the oven igniter

Removed shelves and floor of oven. Removed burner unit to access screws attaching igniter to burner unit. Disconnected wires of igniter. Put new igniter in place and reinstalled burner unit. Reconnected wires using supplied wire nuts. Tested unit. Reinstalled oven floor and shelves once successfully tested. Cooked Pizza.

Removed bottom of oven Removed bottom drawer. Removed two screws holding burner, disconnected both wires.Removed two screws holding igniter,installed new igniter reversing procedure.

Could not get at the screws holding the igniter to the buner, without removing the burner.

Replacing the igniter was easy to do, that only took 15 min. The time was needed to take apart the bottom of the oven so I could get to the nuts on the igniter, and the time to put it back together again. I'm very inexperienced at this sort of thing so since I could do it I'd encourage anyone to give it a go, and anyone that knows what they're doing will do it much faster.

I'm still repairing. The igniter was replaced with new but it still doesn't glow. I'm waiting for a schematic that is being mailed to me from GE. In the meantime I have borrowed a test instrument to check that the system is hot when the BAKE button is pushed. The controls light up as expected but no glow. The BROIL igniter glows when activated, lighting the broiler. The new Ignite was packaged very well so it isn't suspect. I LEFT YOU FOR A FEW HOURS. I tested the electrical with a meter and got zero voltage. I removed the wire nuts and using two alligator clips I connected the meter to the bare wires coming from the oven wall. I then hit BAKE again and BINGO! Replaced the defective wire nut and now the igniter is happy as a clam. --- Thanks for your interest and for expediting the material.

Easy