91195582990 Kenmore Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Scot from Oakland, FL
- Parts Used:
- WB30T10099
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
Large burner on dual element burned out
This was really easy, and pretty with no problems or issues It took me longer to write this than to do the actual installation. I used a digital camera to help me remember where things were, but a pen/paper works fine. Here's what I did:
1. Turn off the breaker for the cooktop.
2. Remove (2) 1/4" hex screws directly under cooktop. You may need to open oven door to reveal them.
2. Prop up cooktop. I used the box the replacement element came in.
3. The element is held in place with (3) brackets held in by a #2 philips screw each. Mark the location of each of the brackets. There are numbers on the element to help you do this.
4. Write down where each of the wires connects to the element. There's only a few of them, but I tend to forget that stuff. The wires have female spade-type connectors that connect to the male ends on the element.
5. Using a needle-nose or small pliers wiggle each wire off the element. Grab the wires by the end of the female connector when you do this. I found it helpful to use a small flat screwdriver to help pry them off. Mine were on pretty tight, so expect this to take a few mins. If you have problems getting to the wires, remove the brackets (next step) first and come back to this one. I let the element hang from the wires without any problems, but I still wouldn't recommend it.
6. Remove each of the screws with a #2 philips screwdriver. Support the element with your hand and gently pull each bracket away from the element. Once they're all gone, the element should just come out. I took a look at my old element and saw that the large burner wires were melted in a couple places, so it was definitely broken.
7. If necessary, clean the underside of the cooktop surface with a clean papertowel. There was a little dust from the old element on mine.
8. Connect the new element and test to make sure it works by turning on the breaker and turning on the burner for a second or two. Note: This will make the top of the element hot for some time, so test it and go away for a few mins. If it works OK, proceed. If not, disconnect and figure out what else may be wrong.
9. Using the old element, make copies of the marks you made for the bracket locations onto the new element. You'll have to punch through the insulation when re-attaching the screws.
10. Re-wire the new element, if necessary and re-attach the brackets over the marks you made. This may be a pretty tight fit because the new element was thicker than the old on mine. I opened up the brackets a bit to make it not so hard to re-attach. Hook the brackets on and squeeze them over the element. The holes in the brackets need to line up with the holes drilled into the bottom of the element. If they don't, spin the element around (or detach and re-attach the brackets) till they do.
11. Screw in the (3) screws over the brackets pushing them through the insulation on the element.
12. Close the cooktop and reattach the hex screws under it (1/4" hex).
13. Turn on the breaker and test again.
Thats it, works great now. Good Luck
1. Turn off the breaker for the cooktop.
2. Remove (2) 1/4" hex screws directly under cooktop. You may need to open oven door to reveal them.
2. Prop up cooktop. I used the box the replacement element came in.
3. The element is held in place with (3) brackets held in by a #2 philips screw each. Mark the location of each of the brackets. There are numbers on the element to help you do this.
4. Write down where each of the wires connects to the element. There's only a few of them, but I tend to forget that stuff. The wires have female spade-type connectors that connect to the male ends on the element.
5. Using a needle-nose or small pliers wiggle each wire off the element. Grab the wires by the end of the female connector when you do this. I found it helpful to use a small flat screwdriver to help pry them off. Mine were on pretty tight, so expect this to take a few mins. If you have problems getting to the wires, remove the brackets (next step) first and come back to this one. I let the element hang from the wires without any problems, but I still wouldn't recommend it.
6. Remove each of the screws with a #2 philips screwdriver. Support the element with your hand and gently pull each bracket away from the element. Once they're all gone, the element should just come out. I took a look at my old element and saw that the large burner wires were melted in a couple places, so it was definitely broken.
7. If necessary, clean the underside of the cooktop surface with a clean papertowel. There was a little dust from the old element on mine.
8. Connect the new element and test to make sure it works by turning on the breaker and turning on the burner for a second or two. Note: This will make the top of the element hot for some time, so test it and go away for a few mins. If it works OK, proceed. If not, disconnect and figure out what else may be wrong.
9. Using the old element, make copies of the marks you made for the bracket locations onto the new element. You'll have to punch through the insulation when re-attaching the screws.
10. Re-wire the new element, if necessary and re-attach the brackets over the marks you made. This may be a pretty tight fit because the new element was thicker than the old on mine. I opened up the brackets a bit to make it not so hard to re-attach. Hook the brackets on and squeeze them over the element. The holes in the brackets need to line up with the holes drilled into the bottom of the element. If they don't, spin the element around (or detach and re-attach the brackets) till they do.
11. Screw in the (3) screws over the brackets pushing them through the insulation on the element.
12. Close the cooktop and reattach the hex screws under it (1/4" hex).
13. Turn on the breaker and test again.
Thats it, works great now. Good Luck
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- paul from west grove, PA
- Parts Used:
- WB44T10009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Broiler element failed
repair took about 30minutes total tiem..first turn off power to stove..then open oven removed racks..used nut drive to loosen top two screw hold element..then remove screw hold temp sensor element...then removed two screws holding broiler element...then removed the top screw ...then pulled element out about 7 inches to expose wire connection..held on with spade lugs.. pulled wires off...element now free to remove ...placed spade lug on new element...put element in pace with top two screws..loosely...then did rear screw that held temp element and broiler element...then tighten all screws ..turned on power..did 15 sec test to make sure wired properly..then 5 minutes to operating temperature... job done...hardest part was crazwling in and out the stove...old bones..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kevin from Leominster, MA
- Parts Used:
- WB30T10045
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Large burner would not get hot
Repair was very simple. Removed 2 screws under the cooktop, tilt the cooktop back, unplug 4 wires from 8" burner, remove two screws holding retaining clips, install new burner in reverse order. Very simple!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jamie from MORRISVILLE, PA
- Parts Used:
- WB48T10011
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
I needed new oven racks
My husband had turned the oven on to cook something and didn't know that I have a plastic tray in there. Well, needless to say I needed to get some new oven racks. I tried to get them through the manufacturer (GE). They were 68$ each. I thought that was a bit steep, so I looked online. I decided to order through PartsSelect. Well...they can 2 days later (the week before Christmas!!)and were a PERFECT fit.
Between the price, shipping speed and quality I will
definitely buy from again and recommend this site to everyone I know!!!!
Oh yeah, I work for Sears too. we have access to all sorts of parts....this site is the BEST for prices and delivery speed!!!!
Between the price, shipping speed and quality I will
definitely buy from again and recommend this site to everyone I know!!!!
Oh yeah, I work for Sears too. we have access to all sorts of parts....this site is the BEST for prices and delivery speed!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frank from St Augustine, FL
- Parts Used:
- WB30T10047
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Coil Burned Out
Open lid,un screw coil,pop in new coil snap holders in place,then cook a steak
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James V. from San Antonio, TX
- Parts Used:
- WB56T10040
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Socket set, Wrench set
The Front Glass of the Oven Door Accidentally Got Broken
The old glass had shattered so I had to clean up the glass fragments from the door including the track where the replacement glass fits. Also, I removed the complete oven door from the stove so I could lay it on the table and work with it better. I had to purchase a star shaped bit in order to remove the two long screws located on the inside of the door. These screws hold the door glass assembly to the oven door. After those two screws were removed, I could get to the remaining interior screws which completely removed the door glass frame from the oven. Once the door glass frame was removed, I placed the new glass into the track and reassembled the frame onto the oven door. Then I reattached the oven door to the range. Oh, by the way, the door is removed from the range by flipping a latch (from front to back) on either side of the door. Then you can remove the door. To put the door back on the stove, just insert the pertruding pieces and flip the lever from back to front (reverse order from how it was removed). You may have to jiggle it a couple of times to get it back into the slot correctly.
I had to learn how to do this as I went along.
I had to learn how to do this as I went along.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JERALD from PHENIX CITY, AL
- Parts Used:
- WB30T10099
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Two part burner, outer ring not working
The outer ring on the adjustable large haliant surface burner of our smooth top stove would not work. It would only work on the small (inner) size.
Found the part on this site, ordered, 3 days later, and it was fixing time.
2 screws removed to lift cooktop, 2 screws to remove old burner and disconnected 4 electric clips one at a time and placed them in same position on new burner. Replace the 4 screws and done.
VERY SIMPLE.
Found the part on this site, ordered, 3 days later, and it was fixing time.
2 screws removed to lift cooktop, 2 screws to remove old burner and disconnected 4 electric clips one at a time and placed them in same position on new burner. Replace the 4 screws and done.
VERY SIMPLE.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- LANCE from ORELAND, PA
- Parts Used:
- WB30T10047
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Heating element burned out.
Unplugged range. Opened oven door and removed two screws from top of oven opening. Lifted oven top and propped up
with a 2 x 3.Unscrewed the two screws that were holding
with a 2 x 3.Unscrewed the two screws that were holding
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- CHARLA from NEW BRAUNFELS, TX
- Parts Used:
- WB23X5340
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Oven sensor was not holding temperature range.
Per the instructions included with part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- daniel from pittsburgh, PA
- Parts Used:
- WB44T10014
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
heating element fractured when cooking easter dinner
removed 2 screws that mounted element. disconnected 2 wires, reconnected wires remounted the element. Done in 5 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from Delmar, NY
- Parts Used:
- WB07X42948
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Range door bottom trim got rusty: a lousy design by GE.
I used a screwdriver and pliers. A nut driver would have been helpful. Oven door is removeable for cleaning and maintenance, but it's heavy and awkward. It has to be laid face-side down to disassemble, so have a protected tabletop ready to avoid scratches. Side trim pieces have to come off to get access to bottom trim mounting screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Apison, TN
- Parts Used:
- WB48T10011
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Don't clean your oven with the racks still in, takes the finish off!!!!
Took old racks out, slid new ones in....exact match at a huge savings from what GE wanted per rack.
Found the company through a Google search, have it bookmarked and will be back if I need something from them.
Found the company through a Google search, have it bookmarked and will be back if I need something from them.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Van from Hyde Park, NY
- Parts Used:
- WB30T10099
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Inner element of dual burner died
-Turn off breaker
-Undo the two screws that hold the top surface down
-Prop up top surface with a board
-Remove two screws/spring clips holding burner
-Transfer electrical plugs to new burner (this was the most challenging part)
-Screw new burner in place
-Lower surface
-Secure surface
-Undo the two screws that hold the top surface down
-Prop up top surface with a board
-Remove two screws/spring clips holding burner
-Transfer electrical plugs to new burner (this was the most challenging part)
-Screw new burner in place
-Lower surface
-Secure surface
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brenda from LaFollette, TN
- Parts Used:
- WB44T10009
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Wrench set
Broiler Unit was burnt out
First I had to remove the oven ceiling screws bracing the broiler element. Second I removed the screws holding the connectors at the back of the oven before I could disconnect the two wires ( which were awkward for me to get to because I am 5'2" but was able to reach without removing the oven door).
I reconnected the two connectors and screwed the brace into the back of the oven. Then replaced the screws into the ceiling of the oven to hold the unit in place.
I was very pleased to have been able to do this project on my own and the broiler is working fine.
I reconnected the two connectors and screwed the brace into the back of the oven. Then replaced the screws into the ceiling of the oven to hold the unit in place.
I was very pleased to have been able to do this project on my own and the broiler is working fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JUDITH from DANVILLE, NH
- Parts Used:
- WB04T10086
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Oven door gasket needed replacement
Replacement was extremely easy. The new part fit perfectly and installed very easily without tools. Also, I received the part within a few days
Was this instruction helpful to you?
Thank you for voting!