91194602300 Kenmore Range - Instructions

Removed the old element and burner bowls and replaced them with the new ones! No screws, no tools needed. PartSelect's prices are cheaper than any other place on the Internet and they shipped me genuine replacement parts, not some 3rd party no-name brand. Also, shipping took less than 2 days! I am thoroughly impressed.

Removed screws holding temp sensor, pulled wire out from behind wall until found connector, disconnected old sensor.
Measured resistance of old sensor and compared with new sensor, they measured nearly the same. Installed the new sensor and tested the stove. Came up to temp ok. No problem since, about 2 weeks.

Replaced element control switches

My stove didn't seem to be getting enough power for the oven to heat up and the burners to get hot enough. When I checked the connection of the electric cord I found that one of the 3 terminals that the plug connects to was broken off. When the new part came I removed the old part by first disconnecting the 3 wires [black,white(ground),red] and then using a small but long 1/4 socket (that I found at Lowes)I removed the 2 screws that held the old part to the stove and the green screw under it holding the flat copper piece that also connects under the white ground wire of the part. I mounted the new piece on with the 2 1/4 screws. The new part comes with a piece of copper that is for grounding the part to the stove. When I compared it to the old part it was a little different. I first screwed the copper piece onto the stove (under the part) with the green screw then I screwed the white wire over the copper piece to the center terminal(you have to make the hole of the copper piece line up to the screw hole). I connected the other 2 wires and then connected the electric cord to the new terminal block and then put the back cover back on the stove and plugged it in. The clock came on I turned on the four burners they all got hot and red. I turned on the oven the element on the bottom got red I then turned on the broiler the top element got red. My stove is fixed.

Pull oven out away from the wall, unplugged from outlet, removed center cover by removing 5 sheet metal screws. disconnected thermostat sensor from control cable. Opened oven door and removed screw that holds thermostat sensor. Pulled thermostat sensor out replaced with new sensor. Plugged sensor in to control cable. Replace panel and screws. Then my wife made me clean the oven. I recommend making the repair when your wife is not home.

First I cut the circuit at the breaker, and then pulled the range from wall to access the access panel. This top panel was held with 4 screws and removable with a standard phillips head screwdriver.

I then removed the 5 wire-crimped fasteners from the defective surface burner switch. (I first labeled these wires to ensure correct placement to the new switch). There were an additional two screws behind the corresponding knob that needed to be removed in order to completely remove the old switch.

The new switch was installed in reverse order to the steps indicated above (two screws behind knob, 5 wire-crimped fasteners, 4 screws to panel). Range was pushed back into position and breaker turned on.

I too made the mistake of cleaning the oven with the shelves in place. It doesn't really harm them...but they turn a tarnished brown color...they look dirty. These replacement shelves were a perfect match. Pricing was reasonable, communication was terrific and shipping was super fast. Happy camper here :-)

Installed the new brackets at the back of the drawer with the 2 screws provided. The new rear mount design is much better than than the old side mount.

The only hard thing was contorting my old beat up body and joints long enuff to reconnect the 2 wires and oven heat sensor and put in 6 screws with a 1/4" nut driver. I did remover the oven door and that made it much easier for me.

I had my husband fix it! Very easy for me.

It didn't take him long. The most difficult part was getting to the screws. He had to practically climb into the oven.

The parts were shipped promptly and the whole process was relatively painless!

Unplugged the power supply. Took off the cover on the back of the unit. Unplugged the wires to the broiler element. Removed the bolts(4) holding the element inside the oven. Removed the temprature sensor from element and took it out. Put it all back the way it came out. Worked great. Took 25 minutes.

Easy

The repair was so simple. First i killed the circuit breaker then removed five screws upluged element from contacts and removed the element plugged new element into the contacts popped the screws back and was done.

It was just a matter of removing 5 screws that attached the broiler coil to oven top. Then carefully removing coil so as not to cause wires attached to fall into the back of the oven. Needed an extra pair of hands to hold coil while i guided the wires back thru the opening. All that was left to do was to secure the broiler coil to oven. All completed in less then 30 mins. A lot easier then originally thought. And, a lot cheaper then getting a repair person to do the job.

After watching the video and ordering the parts and searching for the right size socket (which took most of the time) and finding medical tape as I had no electrical tape I took of the back unhooked the terminals and following the wires to determine which ones needed to be replaced I followed the video instructions on reverse as my son had spliced new terminal blocks into the old wires I taped each new wire to the one it was replacing and pulled it through the back of the stove and into the front attached the new wires to the new block and pushed the clips on the other end of the wires to the knob boxes. I rolled up the excess wire and taped it securely with medical tape so it wouldn't unravel and be in the way when I reattached the back shield on the stove. After I repeated the process for the second terminal (I had two that kept shorting out) I reassembled the stove plugged it back into the wall and used both burners that night to cook dinner! I have had no problems with those burners since then. Really if you watch the video first and follow the instructions you should have no problems. It is really quite simple if someone hasn't tried to repair the problems without replacing the wires. Splicing new blocks into old wires just doesn't work. If I have this problem again, which I hope I don't, I will be confident in my ability to fix the problem myself. Thank you parts select for repair video and the parts.