79075738890 Kenmore Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Milton from Drummond Island, MI
- Parts Used:
- 5304506004
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Broken door glass
I removed the screws holding the door together,removed the broken panel and replaced it with the new glass
The part fit correctly and the re-assembly was easy.
The part fit correctly and the re-assembly was easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dean from Tupper Lake, NY
- Parts Used:
- 5303935066
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Oven would not heat up
First I removed the two screws that held the element in place.I then pulled the element out and cut the wires.I used wire nuts to put the new wirers on and put it back in place with the two screws.I tried it and it worked perfect.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- BETTY from PHILADELPHIA, PA
- Parts Used:
- 5303935066
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
igniter burned-out, not able to start oven
followed directions enclosed.required removal of oven door and old igniter
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Hubert from Street, MD
- Parts Used:
- 5303935066
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Oven of gas range not igniting
Removed lower drawer of oven and base panel of oven. Unplugged stove from outlet. Removed old igniter w/ nut driver (two screws). Disconnected wires (blade connectors) from stove base. Disconnected two-pole plug from oven after removing protective cover in corner.
Install new igniter. You will need to cut existing wires from old igniter so that spade and two-pole connectors can be reused. Join these wires with the new ignitor wires using the ceramic wire nuts provided with the new unit.
Directions are also provided with the new igniter.
Install new igniter. You will need to cut existing wires from old igniter so that spade and two-pole connectors can be reused. Join these wires with the new ignitor wires using the ceramic wire nuts provided with the new unit.
Directions are also provided with the new igniter.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- clayton from rockford, IL
- Parts Used:
- 5303935066
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
would not light
open oven door remove bottom of oven then remome the metal cover over the burner to expose the ignighter remove 2 screws that hold it to the bracket. the two wire's that come out of the ignighter run down under the bottom oven pan, i removed the bottom front cover by lifting up and then pulled out, then i could see the wires i removed the wire nuts and pulled old wires off and removed old ignighter. i pulled off the insulator covers from the old one and slid them on the wires of the new ignighter then i fished the wires back down and and attachted them with the wire nuts, then reasembled the rest of the oven. woks great!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Chicago, IL
- Parts Used:
- 5303935066
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
oven would work intermittently
remove bottom pan, remove gas second cover, loosen nuts on ignitor, cut wires near the ignitor end for extra slack, connect new wire of ignitor, screw on wire caps, reattach ignitor, replace covers and finished. Very easy repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from Akron, NY
- Parts Used:
- 5303935066
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set
oven wouldn't light uneven temp.
had to remove burner bolts holding igniter were stripped cut two wires replaced igniter using two self tapping screws put wires together using wirenuts Honey making cookies right now thanks already told friends about you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephen from Pittsburgh, PA
- Parts Used:
- 5303935066
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Oven would not light
After diagnosing the problem, I entered the Tappan Model #, found the part needed, and ordered from Part Select. On receipt (2 day delivery), I followed the instructions enclosed with the ignitor, and within 30 minutes, had everything up and running. Thanks PART SELECT!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- lois from middletown, DE
- Parts Used:
- 5304506004
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
interior oven door glass cracked
All visible screws on sides & top of door, including screws for the door handle have to be removed. Fairly uncomplicated job, but as the glass that needed to be replaced, was 4th of 4 layers of glass, all needed to be removed from the outside in, in sequence, to get to the broken piece. Then as long as everything was apart, cleaned all pieces, before reassembling. Job much easier with two people, as one can hold & align all layers together, as the other tightens all the screws.
Was this instruction helpful to you?
Thank you for voting!
The tubes which fed gas to the burners were broken due to raising and lifting the top cover which caused gas to leak under the top cover.
I had no experience working on the stove before so it was all new to me. Removed the top cover. Removed the igniters and the burner connections which allowed access to the splash pan. Removed the splash pan and replaced the two broken tubes. Job would have been faster had I known how to access the front burner controls. As a result, we have a fully functioning Tappan range in our kitchen and the range is much better than anything commercially available. They don't make em like that anymore.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ERIC from INDIANAPOLIS, IN
- Parts Used:
- 5304506004
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Broken inside glass
Followed your video and it was not hard at all
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Huston, TX
- Parts Used:
- 5303935066
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Socket set
would not light oven
take off the old by unsceawing it scraw thenew one onput the wires down the back throw the hole put the wires to gather and cap tham plug the elect. back in and turn it on for to test it wow it worked he he ...richard
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- charles from bossier city, LA
- Parts Used:
- 5303935066
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
oven would not allow gas to flow for igniter to light
removed broiler front by depressing the indents on the door slides, removed two screws holding igniter cut wires on old igniter and spliced new igniter to existing wires with supplied wire nuts then reinstalled new igniter and tested have been using oven ever since
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from MANASSAS, VA
- Parts Used:
- 5303935066
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Oven glows but won't ignite
Thank you, Thank you and thank you!!! I couldn't be happier and I save over $200 in repair. My repair was very easy after watching the video. I cut off the wire and ensure that the new one are attached into place. Placed all parts back and boom, the oven starts working a new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JERRY L from PIPER CITY, IL
- Parts Used:
- 5303935066
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Oven wouldn't light
Removed oven door, removed oven floor. Unscrewed skirt with attached igniter and gas tube. Two nut screws hold igniter to burner. Remove old igniter and replace with new, reattach two wires with supplied wire nuts. Replace oven floor and door. Oven lit right up, pizza anyone?
Was this instruction helpful to you?
Thank you for voting!