Models > 9119808510 > Instructions

9119808510 Kenmore Range - Instructions

Jump to:

All Instructions for the 9119808510
46 - 60 of 320
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Donald from Gulf Breeze, FL
Parts Used:
WB44K5012
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Nutdriver, Screw drivers
Oven wouldn't heat - wire not exposed
Removed two screws and removed the oven elelent. One wire was not through the back of the stove. Ordered new element anyway. Slid stove out (slide-in model). Unplugged power. Removed two covers protecting wires on back of stove. Found wire for oven element. Had to cut and strip end of wire and use new blade clip. Crimped new clip to wire and inserted into oven through back of stove. Replaced covers. Plugged oven element to wires and tried out oven. WORKED ! Saved new oven element for next time. Difficulty encounted was lack of knowledge on where stove was screwed into counter-top and what size blade clip to buy. It always helps to have a dog 3" away just itching to lend a paw.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Arthur from Indian Harbour Beach, FL
Parts Used:
WB21X36771
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers
Halogen element staying on
removed the end caps from the stove panel, unscrewed the back, unscrewed the old switch, CAREFULLY noting which wire went to which terminal, removed the wires.
Reversed the process. took a little longer because I felt compelled to do a thorough cleaning while I was there.
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Fareed from Randolph, NJ
Parts Used:
WB44K5012
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver
Bake element caught fire and melted
Turn off power at the circuit breaker before working on electric thing.

Removed oven door and shelves for free access to element. Unscrewed the old element, pulled it out, removed the clips and removed the element. Reversed these steps to install the new element. Tested the element to ensure it worked.
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Linda from Fort Collins, CO
Parts Used:
WB44K5012
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver
The bake element was burnt out.
It took a nutdriver to remove two nuts. The defective element was removed and the replacement installed. It works great!
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Kathy from madison, WI
Parts Used:
WB44K5012
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Wrench set
Uns rewed and pulled out
At first thought I was taking out some insulation but. "Clamp" just slid off and was very easy to install! Finding the right size socket took longer than the repair!
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Robert from HOUSTON, TX
Parts Used:
WB17X210
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Old Terminal Block was arcing.
Cut Wires to old terminal block and wired in new Terminal Block
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
lynette from Bowling Green, KY
Parts Used:
WB44K5012
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers
Element burned out.
Flipped off the circuit breaker first. Unscrewed the two screws holding the element in place. Pulled out about 4-5 inches. Tried several times to pull apart the connections, finally got 'em - don't give up (I must have weak fingers). Then plugged in the new element, shoved the wires back in, screwed it back in place, flipped circuit breaker back on, turned the oven on.... made brownies (o:
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
MARTIN from NAPERVILLE, IL
Parts Used:
WB44K5012
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver
Lower oven heating unit burnt out
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires,held wires one at a time so tehy wouln't slip back into rear holes in oven, slid off connector tabs and pushed on to replacement unit...)
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Coleen from Danville, IN
Parts Used:
WB44K5012
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
The old heating erlement basically melted and broke in two places
I unscrewed the two screws inside the oven, then i pulled the oven away from the wall and unscrewed the protective shield, and undid the wiring. Then i removed the element. Once the new one arrived, i pretty much just did the same thing in reverse. vwa-lah... fixed!
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Jan from Rockport, ME
Parts Used:
WB44K5012
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers, Socket set
Oven would not get to temperature...200 degrees max
Pull out oven and unplug from 220 outlet. Remove rear upper/lower cover (4 screws), Remove two wires from rear of element. From front, open oven door, remove two screws and pull out old element.
Install new element by reversing above sequence. Then test and push oven back in place. Easy!
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Franz from CRESTVIEW, FL
Parts Used:
WB44K5012
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver
Oven would not heat
Removed old broken element and installed new one. Took less than 10 minutes
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
linda from STANTON, MI
Parts Used:
WB32X107, WB32X106
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
the drip bowls were worn out
simply replaced them.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Kathleen from INCLINE VLG, NV
Parts Used:
WB32X106
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Drip bowl from a big box store was too big even though both say 8”.
Ordered the part and set it in.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
William from MARTIN, GA
Parts Used:
WB44K5012
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Pliers
bake element was fried
I went by the video
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Richard from NEW BERLIN, NY
Parts Used:
WB44K5012
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver
element broke
took 2 screws out that held element in, pulled old element out of oven wall, unhooked the wires. Hooked the wires to the new element, pushed it back into the oven wall, replaced the 2 screws.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the 9119808510
46 - 60 of 320