9119698890 Kenmore Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- William from MARTIN, GA
- Parts Used:
- WB44K5012
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
bake element was fried
I went by the video
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Franz from CRESTVIEW, FL
- Parts Used:
- WB44K5012
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Oven would not heat
Removed old broken element and installed new one. Took less than 10 minutes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Greer, SC
- Parts Used:
- WB14X104
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Broken Hinge
Assumed this broken hinge was going to be an expensive service call. Decided to try and fix it myself. Ordered the part off partselect.com and got some repair tips off the website that made this a breeze. I am not handy at all but was able to complete the replacement in less than 30 minutes and spent only $30 on the part. Just needed to unscrew the old hinge and release the spring from under the stove (which I accessed by pulling out the drawer). It would have cost me over $100 to just get a service person to look at it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Linda from Fort Collins, CO
- Parts Used:
- WB44K5012
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
The bake element was burnt out.
It took a nutdriver to remove two nuts. The defective element was removed and the replacement installed. It works great!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephen from Peru, IN
- Parts Used:
- WB14X103
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Oven would not fully open. Could see the broken roller on the hinge.
Removed the door. Unscrewed the hinge from front of oven. Took broiler drawer out. Unhooked the spring. Removed hinge. Screwed new hinge in. Rehooked the spring. Slid oven door back on hinges. Mission accomplished. Oven door works like a champ. Wife happy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- allen from MT. AIRY, MD
- Parts Used:
- WB44K5012
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
bake element was broken
i slid the oven out unplugged it !! , removed back cover with a nut driver, removed the two retaining nuts from the old bake element ,opened oven door removed two nuts that hold bake element to the back of the oven , installed new bake element then attached wires in the back of oven to the new element re installed retaining screws inside oven , check to make sure screws that hold power cord wires to the over are TIGHT !! i then installed rear cover then plugged in the oven it worked great !!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Douglas from Corvallis, OR
- Parts Used:
- WB44K5012
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
Replace bake heater element
Basically very easy. Be sure to follow suggested safe practices - DO shut off the circuit breaker to the unit BEFORE starting (I didn't to start with, shorted out the heater leads - dumb on my part). Just removed the burned out element by removing the 2 screws using a nutdriver, pulled the element out, and slipped off the crimp fittings. Reverse steps to install replacement. The crimp fittings were stubborn coming off the old one, so it took longer than expected. Otherwise, easy peasy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Derrick from Ypsilanti, MI
- Parts Used:
- WB44K5012
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Oven no longer heated except for Broil element
1)Unscrewed old baking element from wall of oven
2)Detached old baking element from wires
3)Attached new baking element to wires
4)Screwed new baking element to wall of oven
5)Turned on oven
2)Detached old baking element from wires
3)Attached new baking element to wires
4)Screwed new baking element to wall of oven
5)Turned on oven
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jan from Rockport, ME
- Parts Used:
- WB44K5012
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Oven would not get to temperature...200 degrees max
Pull out oven and unplug from 220 outlet. Remove rear upper/lower cover (4 screws), Remove two wires from rear of element. From front, open oven door, remove two screws and pull out old element.
Install new element by reversing above sequence. Then test and push oven back in place. Easy!
Install new element by reversing above sequence. Then test and push oven back in place. Easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from CLAY, NY
- Parts Used:
- WB44K5012
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
The phillament ends were pointed straight and the one I removed from the oven were bent in an angle .
Bent the tips so the phillament can fit inside the oven.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- lynette from Bowling Green, KY
- Parts Used:
- WB44K5012
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
Element burned out.
Flipped off the circuit breaker first. Unscrewed the two screws holding the element in place. Pulled out about 4-5 inches. Tried several times to pull apart the connections, finally got 'em - don't give up (I must have weak fingers). Then plugged in the new element, shoved the wires back in, screwed it back in place, flipped circuit breaker back on, turned the oven on.... made brownies (o:
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MARTIN from NAPERVILLE, IL
- Parts Used:
- WB44K5012
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Lower oven heating unit burnt out
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires,held wires one at a time so tehy wouln't slip back into rear holes in oven, slid off connector tabs and pushed on to replacement unit...)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Howard from East Orleans, MA
- Parts Used:
- WB44K5012
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Socket set
oven heating element burned out
First turned off the power to the stove at the breaker panel, thenI removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. Disconnecting/reconnecting the "clips" was the only difficult part because they did not slip off/on easily. Replaced the element in the oven, replaced the screws...good to go!
Best part of buying from Parts Select was that they shipped the part the same day I ordered it, which was the Friday after Christmas. Competitor would not have shipped till the following Monday and we needed the oven ASAP!
Best part of buying from Parts Select was that they shipped the part the same day I ordered it, which was the Friday after Christmas. Competitor would not have shipped till the following Monday and we needed the oven ASAP!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Coleen from Danville, IN
- Parts Used:
- WB44K5012
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The old heating erlement basically melted and broke in two places
I unscrewed the two screws inside the oven, then i pulled the oven away from the wall and unscrewed the protective shield, and undid the wiring. Then i removed the element. Once the new one arrived, i pretty much just did the same thing in reverse. vwa-lah... fixed!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Fareed from Randolph, NJ
- Parts Used:
- WB14X104
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Over door would not open fully; light was always on
Slid off the oven door and loosened the hinge assembly. Removed the storage drawer to unhook the spring and then took off the old hinge assembly.
Inserted the spring into the new hinge assembly and then installed it - just tightened the screws. Hooked the spring into the lower point. Slid in the oven door and tested it so that is opened/closed easily. Cleaned under the oven while the storage drawer was out.
We can now bake bread, pizza, etc. What a relief.
Inserted the spring into the new hinge assembly and then installed it - just tightened the screws. Hooked the spring into the lower point. Slid in the oven door and tested it so that is opened/closed easily. Cleaned under the oven while the storage drawer was out.
We can now bake bread, pizza, etc. What a relief.
Was this instruction helpful to you?
Thank you for voting!