36272322101 Kenmore Range - Instructions

Easy

Remove the old tubes. Lift the lid NO MORE THAN FOUR INCHES. !!!!! Feel for the connections on the switch ends and attach losely. Carefully ( with some slight bending ) attach tubes to the burners. Tighten all connections. Do not over tighten.
The tubes broke originaly because , attempting to clean the area I lifted the lid too high.

Removed screws to back plate, unplugged, removed controller and installed new.

My son lifted up cooktop, unscrewed the front plate to gain access to old tube burners, removed and replaced with new parts.

The part that was ordered based on the shamanic wasn't the part that was needed for the repair. It was to short. I took the other screw for the other side and that screw was an inch longer than the screw that was ordered thru your company. I then went too a jar that I placed extra screws, nuts and bolts which l keep in my garage . I found a same length screw but a different head and it works perfectly fine. When I ordered the part from your company most of the parts did not have a photo of the part on file, or a description like how long the part is. I still ordered it because it should fit the make and model number that was posted on the shamanic that was showed to me on line.

Turned off circuit breaker, Then pulled out range, straight out and away from wall and cabinets. Layed braket on flooring and moved stove back in to make certain it aligned with range rear stands. Moved range back out, marked holes in braket, screwed in screws to anchor bracket. Pushed range back into placed against wall. Tried to |"tilt" range by pulling down on door after opened - range was held in place sre

Very easy to remove grates, burner cover and remove old burner head. Very simple process, but surprised that there was no efficient way to clean carbon deposits from my old burner. Burner video instructions on line insured I installed the new burner head correctly (actually, pretty hard to get wrong), and burner worked correctly immediately. Will likely replace other burners in time as the new one is so "silvery" colored compared to my other burners.

Remove light bail, glass cover held by two nut screws. Pull socket, removed clips in back, replaced wire connectors, placed new socket in, then glass cover and bail. Wire connected in back, cover plate replaced.

called appliance repairman. He found problem and ordered new part. After 2 months waiting for part to get there, my husband got on internet and calld your number, and ordered what was needed. Now for the great thing. Within 4 working days we received what we thought we needed. but we had ordered the wrong part number. Got back on internet, went right to your web site, found the part that we did need, a flame spreader instead of the Deflector. called your service number, talked to a very nice person, again, told her what we did and ordered the correct part. Another great thing, we got that part the very next day. I returned the wrong part that same day. We then had our son install it and now we have a very nice working oven. Though out this very long ordeal, we talked to the applicance service people and got the same answer. The part has been ordered and it should be here next week. When we found your web site and called for the part, I called the appliance service and told them we had ordered the part ourselves and I would be happy to give her this information. THE VERY NEXT DAY she called us to tell us the part had fially arrived and they could come out the next day. Told them sorry but it as already taken care of. The very next time we need some part for any appliance we will call you first. Thank you for your very nice service people and the fast way that this all took place.

loosen the compression fitting both ends and screwed new ones in place .

The person I spoke to knew exactly what I was trying to describe. The part arrived in 2 days. 5 minutes later the drawer was back in place. I was glad I save the screw as the part did not come with one.

Used screwdriver w/star bit to remove two screws (longer one on top). Removed cracked end cap. Placed new end cap into position, making sure all tabs were correctly aligned. Replaced screws (top one first)tightening them slowly & alternating back & forth so as not to crack the new part.

The only tool needed was a nutdriver to remove the lamp socket. I needed my head mounted light to see what I was doing, and everything went smoothly from there. Simple job.

Pulled range out from the wall. Un-screwed 4 screws. Disconnect old control board. Plugged in new board. Easy, easy, easy! We used the old overlay. It peeled off easily. If you want a new one, be sure and order it as well.

Removed the back panel. Removed the electronic control board, four screws. Four electrical posts didn't match up exactly, but it wasn't too difficult to figure out because of labeling.