79071424400 Kenmore Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Mary Ann from Hawley, PA
- Parts Used:
- 5304414035
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
bottle fell and clipped edge of range
Touch up paint was easy to apply. I gave it a few coats and you cannot tell where to chip was. I wish you had a standard mail delivery option. I paid twice the price of the paint for fed ex delivery. I didn, t need the paint next day but it did get here before the estimated deliverydatee.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Columbiana, OH
- Parts Used:
- 316233903
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Temp did not match readout.
Replaced temp probe and checked OK. This model did not have a full back as the instructional video showed. No cover to remove at all. Only suggestion might be to include two wire nuts of proper size. Average wire nut would be too big. Fortunately, I happened to have a couple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Manasquan, NJ
- Parts Used:
- 316495901
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Bottom Panel of over rusted out.
Unplug the stove from the wall socket. Remove the oven door as shown in the instructions for replacing the door. This makes the job a lot easier. At the rear of the bottom panel there is a screw at each corner. Remove these screws, a screwdriver will loosen them, then remove by hand. If you have a convection oven remove the fan cover as this prevents the bottom panel from coming out. There is a screw at the top and the bottom of the cover. You can then gently lift the bottom panel at the rear and work it out of the front lip. Install the new bottom panel in reverse order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Matthew from Gladwin, MI
- Parts Used:
- 316237805
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Wrench set
burner would not light
We took off all of the bolts holding the burner assembly's in place . Then took the top of the s range off. Used a wrench to remove the old assembly and re-placed it with the new one. It took longer to get all of the top and under cover off then to put the new part in. Very good service from Part Select. MATT
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Vernon from Moorehead, KY
- Parts Used:
- GRLP3
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
bought a used gas range i have propane it was natural gas
changed the orfices with a 10mm socket and driver handle used an adjustable wrench to tighten the orfice in the bottom of the oven approximately 45 minutes we were using the range
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Randall from Fernwood, ID
- Parts Used:
- GRLP3
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Convert NGas to LP
The Conversion Kit was throughall with extra fittings and good instructions. My problem was haveing to pay a lisence gas installer $65.00 an hour to do a safety & pressure test. Maybee future Conversion kits would include a cheap disposable pressure tester with hose, then it would be a complete done job by the owner.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenneth from Edgemount, SD
- Parts Used:
- 316233903
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Socket set
Oven Temperture probe.
Would have been simple if Frigidare had not changed the plastic snap wire connector on the part. The replacement part had a different snap together wire connection. After a couple of phone calls stating that the new part and the old part had different part numbers was informed that you have to snip off the ends and use wire connects but it was the right part. Once I knew that it was a simple repair if you have the wire connects to connect the wires.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Hiawassee, GA
- Parts Used:
- 316233903
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Socket set
wrong temp when baking.
removed back. discovered wrong connector on probe. Cut the connectors off and spliced with small butt connector. Took me longer to find the tools and connector than to do the repair. The wires are very small and require a very small butt connector. Tips by the sales rep and previous customer were helpful. Great service. Will try PartSelect for Cub Cadet and Yamaha OB parts. Thanks. John
Was this instruction helpful to you?
Thank you for voting!