91194404301 Kenmore Range - Instructions

Very easy repair. The gasket ends are stuffed into slots right below the oven window and the gasket is held in with small wire clips that pop into holes in the door. Just pull the old gasket off, no tools. Install the gasket starting by stuffing one end into the slot mentioned above until the first clip lines up with the first small hole. Then insert each successive clip into the corresponding holes. Then use a slot screwdriver to stuff the other end of the gasket into the second slot. No sweat.

Unplugged appliance and removed 5 screws on back of stove/oven and removed plate. Disconnected the sensor and unscrewed it on the inside of the oven. Pulled the cord through and replaced with new sensor. Replaced all parts and plugged in the appliance and tested. Worked great.

The repair went very easy. The replacement part was designed differently than the original part. It installed on the rear of the drawer with a screw as the original snapped into the side. This was a bit confusing when researching and looking up the part online.

I started by lifting the front of the stove and slipping a towel under it so it would slide easier and not scratch the floor. The next step was to unplug the stove, after that, I removed the shelves. The next step was to remove the cover plate on the b ack to expose the connection. I removed the old element by pulling the to slide-on connections and the two mounting screws. At this point I took the time to clean the oven since the element was not in the way. To install the new element I did the opposite of th removal process.

First, I made sure the power was turned off at the breaker box so I didn't electrocute myself. Then, I took out the 2 screws that hold the element in place, then pulled it out and unplugged the wires.
I plugged the wires onto the new element, and replaced the screws. My daughter could have done this....

The repair was simple. All wires were color coded and the new part had the same color codes marked. Simply unplugged the wires from the bad part and plugged them into the new part a reinstalled the part to the back panel of the range.

1) pull out the stove
2) remove the 7 sheet metal screws holding the back panel on. (the panel that also covers where the cord splits and connects to the oven.
3) Find the small plastic connector located in the middle of the back of the range and unplug it.
4) open the front of the oven and remove the one screw holding in the oven temp sensor.
5) replace the sensor and make sure to "feed" the new cord through as best you can.
6) I had to dig through the insulation a little bit to find the new wiring harness
7) connect the wiring harness and put the back of the range back on

note: this was very simple to do if you think this might be the problem don't hesitate to handle this one yourself.

Took old racks out, slid new ones in....exact match at a huge savings from what GE wanted per rack.
Found the company through a Google search, have it bookmarked and will be back if I need something from them.

Two screws on the inside to free element. 4 screws in the back to remove a plate. unhooked element connectors. Remove element from inside replace with new one. Too Easy.

Real happy on how fast the new part came.
1.Pulled oven away from wall and unplugged the unit & removed baking racks.
2.Removed the back wire cover behind the oven (3 screws).
3.Used the nutdriver to carefully remove the two holding screws inside the oven. Then I pulled the element towards me to expose the wires.
4. Using the pliers, I disconnected the element from the wires.
5. Using my son's help, I had him push the new element leads into the holes in the back while I connected the leads to the wires behind the oven.
6. Replace the two element retaining screws inside the oven.
7. Replaced the rear panel with the 3 screws.
8. Put the oven back in place and plugged it in. The oven worked perfectly!

I turned off the breaker for the oven. I used a electric drill with a 1/4 in socket to unscrew the two bolts inside the bottom of the oven. Then I pulled
out the heating element and slid off one connector and attached it to the new element. Then I slid off the other connector and attached it to the new element. Then I screwed the bolts back. I turned the breaker back on and it worked great.

Turn off circuit breaker.
Lockout (LOTO) circuit breaker.
Pull stove away from wall to access the rear of range.
Remove seven (7) screws from rear cover with nutdriver / screwdriver.
Carefully, disconnect stake-on terminals (wires) from element (may need to use needle nose pliers).
Open oven, remove racks.
Remove two (2) screws holding element in place with nutdriver.
Remove old broken element.
Insert new element. Fasten with screws previously removed. Close oven door. Go to rear of unit.
Reconnect wires to element. Make sure insulation seals around the element.
Inspect for any other damage; repair as may be required.
Replace cover panel and fasten with the seven screws previously removed.

Does not hurt to vacuum and clean the area stove, too.
Push stove back into position.
Remove LOTO and turn on circuit breaker (power)

Turn oven on to highest temp to bake off any contaminates on element. Turn OFF. Let cool. Replace racks a/r. Close oven door.

Invite the pretty girl next door to come over to bake something.... OK, this part is optional.

Replaced temperature sensor in the oven first ($10 part, always start with least expensive possibility!), but that didn't solve the problem. 5-10 minute repair, not counting moving the range in and out of it's home between cabinets. Next replaced the control board ($90 part) which solved the overheating problem. 15 to 30 minute repair, don't be intimidated by all the wires. Remember to turn off power at the breaker (duh). Order the faceplate graphic ($37 part) because chances are the old one won't peel off cleanly (ours didn't, "I was really careful Honey!!) and the otherwise excellent PartSelect.com website doesn't suggest the part might be needed. Anyway, I saved a minimum of $80 plus Labor by doing it myself. I had the advantage of living about 100 miles from their warehouse and got NEXT DAY delivery from FedEx instead of 3-5 business days. Suggest you order before noon.

Repair: unscrewed the back panel- 2 screw and the sensor and bake element from the inside had 2 screws each. Just stuck them through their old hole from inside to the outside, pushed plug back together. Then screwed back into place, screwed back plate back on. Plugged stove in, turned on the oven and within 2 seconds the bake element was blood red and temp. was up to 350 in less then 10 min. Come to find out only needed the oven sensor -$10.00part but I already ordered the bake element so I went a head and replaced it - cost $50.00. Have a great oven again for less then $70.00repair.

First I had to remove the oven ceiling screws bracing the broiler element. Second I removed the screws holding the connectors at the back of the oven before I could disconnect the two wires ( which were awkward for me to get to because I am 5'2" but was able to reach without removing the oven door).

I reconnected the two connectors and screwed the brace into the back of the oven. Then replaced the screws into the ceiling of the oven to hold the unit in place.

I was very pleased to have been able to do this project on my own and the broiler is working fine.