79095882302 Kenmore Range - Instructions

First, I disconnected the electrical power by pulling apart the plug behind the range. Next, I removed the screws holding the service plate on back of the top panel.I removed the switch knob by gently pulling it from the stem. Underneath I found 2 screws holding the switch in the panel. I removed these with a phillips screwdriver.I was able to pull the entire switch out to the rear leaving all wires attached.The new switch looked different from the original and the wires were configured differently but the wires were clearly marked. By removing one at a time and placing it on the new switch to the corresponding marking,it was a simple matter to wire the switch.I reinstalled the switch in the panel,put back in the screws to hold the switch, slid the knob back on the stem, reinstalled the rear panel,and plugged the power cord back in.The switch worked perfectly.

replaced temp probe per your suggestion. No improvement! checked both heating elements with ohm meter. OK Next suggestion was replace circuit boards. Bought new range for less than cost of 2 oven/range control boards.

I unplugged the stove. Then I lifted up the top of the stove to expose the burners. I unscrewed the necessary screws and plugs that attached the old burner to the stove. Then I simply put the new one back in it's place. The stove was one of those flat burner stoves, and I was a little concerned that I would be able to do it. The repair man wanted to charge me $150.00 for labor.

Pulled stove away from the wall and unplugged it. Removed probe and cut the wires because the connection clip on the new probe was different from the original. Leave the wires as long as possible because you will need the extra length to splice the clip from the old probe to the wires on the new one. Replaced probe and plugged the oven back in. Done.

took door off and tore it down making sure of each step so I could put it back together, removed broken glass and replaced with new piece and reassembled. It was difficult to get the door back on the hindges alone I would suggest seom help at that point. Also pulled oven away from wall and took off back cover unbolted the temperature probe and removed. New probe did not have the same connector (problem) so you have to splice the two together, I did not like that but it works. This is a simple repair and did not take very long to complete. Everything is working fine.

Removed outer glass first ,then worked my way thru to inner glass..

removed back. discovered wrong connector on probe. Cut the connectors off and spliced with small butt connector. Took me longer to find the tools and connector than to do the repair. The wires are very small and require a very small butt connector. Tips by the sales rep and previous customer were helpful. Great service. Will try PartSelect for Cub Cadet and Yamaha OB parts. Thanks. John

I was unable to loosen the screws myself so I called my friends husband to help me. We watched the video together and followed the instructions. The door in the video was a bit different than mine but this repair was easy.

Really straightforward - just took door off of the hinges and worked taking it apart until I got to the front glass that was cracked. Took it out and put the new piece in and reversed the process. Really easy and I got to clean each piece on the way back in to get rid of some spills.

I followed directions for replacement of the glass from the web. Replacement was simple and easy.

Removed oven door. Removed screws from bottom of door as well as handle screws. Remove inner panel to expose glass. Replaced glass panel and reverse steps. Very easy.

Turned off electric at the main box. Removed glass top. Used a razor knife to pry the connections loose so that the new connections could be slid in. Problem was that the element ordered looked entirely different then the original one. Even the hookup was different. But once the connections were made, the ceramic top placed on top, and the electric restored everything seemed okay. The warmer works and when it heats up the warning light turns on. When the warmer cools the warning light goes off as it should.

removed the door from the range. removed the 4 layers of glass and carefully set aside the unbroken ones. the 3rd and 4th glasses were held together with a metal frame which had to be dismantled. The old broken glass was rusted and hard to get out of the frame. It had to be cleaned thoroughly of broken glass and rust. the removal process could then be reversed to assemble the parts and re assemble the door to the front of the range