66575004104 Kenmore Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Brett from Arlington, WA
- Parts Used:
- WPW10293048
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench (Adjustable), Wrench set
Oven did not rise to temperature when at the bakie setting
First make sure it is the gas valve not the ignitor. If the clicking sound still happens then the ignitor is fine, no clicking means ignitor may be broke and try to fix that first because it is cheaper. For us I knew it was the valve because the ignitor still clicked and the broil and top elements still worked. After the part arrived I turned off the gas and pulled the power to the oven. Disassembled all the components taking pictures along the way to remember what it looked like to go back together. Installed the new valve and use yellow gas tephlon tape at the seals. Put components back in reverse order. Run the top elements first to get gas in all the gas lines and remove the air. At this point the oven bakes again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- dennis from tonganoxie, KS
- Parts Used:
- WPW10107820
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Oven Self Clean Would Not Function
Take off the back panel of stove and unplugged timer motor and switch on door latch assembly,removed two screws that hold assembly and slide rod off. I put 110 volt plug to timer motor and it did not move, that is how I diagnosed problem. Ordered new assembly (cannot buy just timer motor)put new door latch assembly on and worked fine. Of course unplug stove before you start !
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeff from Manhattan, KS
- Parts Used:
- WP8053334
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
broken rear drawer glides
just replaced the broken glides with the new ones.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from Cornelius, NC
- Parts Used:
- WPW10181986
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
oven temperature did not stay as set
changing the part itself was easy, but the sheet metal covering the whole back of the oven was difficult to remove because of some screws that were stripped. The new sensor solved the problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Sullivan, IN
- Parts Used:
- WP8053834
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Broke outer glass on oven door.
Repair relativley easy only needed phillips screwdriver to complete repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Fairfield Bay, AR
- Parts Used:
- WPW10107820
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Could not get self cleaning oven to engage
Removed back of stove, 8 screws, removed original latch assembly and installed new assembly. One thing that can cause you difficulty is that the rod that connects the assembly to the front latch on the door can disconnect and has to be reconnected.[Problem]
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Randall from Corona, CA
- Parts Used:
- WP9757218
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Wrench set
Valve stem broke at the knob
Lifted the top disconnected the old valve and replaced with a new one.I believe the valve should have been shipped with two gaskets,. One for the bottom and another for the top. I reused the old one on the top with no problem but would have preferred a new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Diane from Elyria, OH
- Parts Used:
- WP8523175
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
The original trim rusted
I did the repair by myself. I used masking tape to hold the side trim in place. It was pretty easy and it looks great.
Was this instruction helpful to you?
Thank you for voting!