Models > 9114658810 > Instructions

9114658810 Kenmore Range - Instructions

Jump to:

All Instructions for the 9114658810
91 - 105 of 424
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
lynette from Bowling Green, KY
Parts Used:
WB44K5012
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers
Element burned out.
Flipped off the circuit breaker first. Unscrewed the two screws holding the element in place. Pulled out about 4-5 inches. Tried several times to pull apart the connections, finally got 'em - don't give up (I must have weak fingers). Then plugged in the new element, shoved the wires back in, screwed it back in place, flipped circuit breaker back on, turned the oven on.... made brownies (o:
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
William from West Liberty, KY
Parts Used:
WB21X36771
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Pliers, Screw drivers
Knob/switch would not turn right front burner on at all!
Pulled range out from the wall. Unplugged cord from outlet. Removed old knob, removed two phillips screws a very top of chrome trim, removed six nut-head screws from back to reveal the switches...removed two set screws from the front at knob base. Visually checked to make sure wiring post of new switch matched the old one. There was enough slack in the wiring to remove one wire at a time and connect it to the new switch in its appropriate place. Put new switch in the panel and secured with the two set screws. Select the bushing that would take up the slack for the old knob to fit on the new switch stem. Held new stem at its base with pliers and used another pair of pliers to snap the stem at appropriate length. (The new stem could not be broken off short enough to have the knob as flush to the panel as the other knobs...this was the only negative factor in the repair) Replaced nut-head screws and phillips screws. I was especially pleased with the quick delivery of the part...even without special shipping rates I received the part in less than 18 hours from the time I ordered it online!
3 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Lonnie from Nipomo, CA
Parts Used:
WB14X104, WB14X103
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Oven door hinge rollers had broken.
The repair went surprisingly well! My only problem was the bottom screws needed WD40 to loosen, but otherwise the parts went in easily.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Douglas from Corvallis, OR
Parts Used:
WB44K5012
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Pliers
Replace bake heater element
Basically very easy. Be sure to follow suggested safe practices - DO shut off the circuit breaker to the unit BEFORE starting (I didn't to start with, shorted out the heater leads - dumb on my part). Just removed the burned out element by removing the 2 screws using a nutdriver, pulled the element out, and slipped off the crimp fittings. Reverse steps to install replacement. The crimp fittings were stubborn coming off the old one, so it took longer than expected. Otherwise, easy peasy.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
linda from STANTON, MI
Parts Used:
WB32X107, WB32X106
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
the drip bowls were worn out
simply replaced them.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Kathleen from INCLINE VLG, NV
Parts Used:
WB32X106
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Drip bowl from a big box store was too big even though both say 8”.
Ordered the part and set it in.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Richard from NEW BERLIN, NY
Parts Used:
WB44K5012
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver
element broke
took 2 screws out that held element in, pulled old element out of oven wall, unhooked the wires. Hooked the wires to the new element, pushed it back into the oven wall, replaced the 2 screws.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Allen from McCalla, AL
Parts Used:
WB14X103
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers
hinge roller broke
first open oven door a couple inches and slide door up off hinges, then removed storage drawer to gain access to hinge spring, remove hinge spring with pliers noting which hole spring was attached in.then remove three screws from hinge and installed new hinge put three screws in attached spring back and put storage drawer in and oven door back on.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Mary from CHARLESTOWN, IN
Parts Used:
WP660533
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Element did not heat
Pulled out element, plugged in new element. About 5 seconds.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
DAVID from PETALUMA, CA
Parts Used:
WP660533
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Oven Wouldn't Heat
Of course, power off first, then I removed the old one and inserted the new one, make sure everything in right place, then turn on power, simple as 1-2-3.
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
William from MARTIN, GA
Parts Used:
WB44K5012
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Pliers
bake element was fried
I went by the video
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Rosemary from BROOKFIELD, CT
Parts Used:
WB32X106
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Needed new drip bowl, was very hard to find one that fit my stove
Installed easily, was most impressed with the speed of delivery and it was the perfect size!!
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Catherine from SEATTLE, WA
Parts Used:
40A15
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
The light inside the oven had burned out
0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.

No tools needed, the cap is just held in place with pressure from the wire.
3 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Ricky from LAWRENCEBURG, KY
Parts Used:
WB14X103
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers
Hinge broke on range. Oven door was very hard to open.
Followed the instructions from the video. The repair was really easy and quick.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Karilyn from KEWADIN, MI
Parts Used:
WB32X106
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Drip pan was ruined by renter
I ordered a new drip pan. Piece of cake. Stove looks new again.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the 9114658810
91 - 105 of 424