9119328813 Kenmore Range - Instructions

Called in and talked to someone and he look yup what he thought was correct but after i got them theywere wrong so i sent them back for a full refund minus 9.90 freight. I still need to figure out what i need for my 27 inch wall oven. Please help. Thanks

Remove oven door from hinges, by pulling it straight up and off, (like you would do for closer access to clean inside). Remove the storage drawer. Lift up and away off the track, (like a file cabinet drawer). With the drawer out and away, you can see how the springs are easily detached from each hinge. Note the location of where the springs attach to the hinges, and bottom of stove. Remove each spring. Three screws on each side hold the hinges on. Unscrew, and set them aside. (The new hinges did not have new screws in package.) Place new hinge in place. Reinstall in reverse of disassembly. If any part of the door or face of the stove (where hinges mount) was bent slightly due to forcing door open, reform with light hammer taps and C-clamps. Enjoy for ANOTHER 10+ years, because it's a GE Profile Stove : )

replaced lights in refrigirator and freezer

Lifted the door off the hinges, unhooked the spring from each hinge, unscrewed 3 Phillips head screws from the face plate of each hinge and removed the hinge assemblies . Hinges went in the way they came out; easy shmeasy. Took less than 15 minutes and the door is like new.

With multimeter checked resistance of oven sensor. Specs called for 1100 ohms. It was off by 27 ohms. The sensor from Part Select had exact wire connection as original. Then just matter of undoing old and reconnecting with new one.

One unsatisfactory event. I asked Part Select why my clock did not work or light up(timer works ok) . Answer was: sorry we have no time to help you. That soured the otherwise happy experience.

repair went fine, real easy.

After tilting the oven door out and sliding it up to remove it, I slid the storage drawer our completely from the range. After removing the spring that held the hinge assembly under tension, I removed 3 phillips head screws that held the existing assembly in place and removed it. After verifying the part you sent was an exact match, I reinstalled the new part, fastened the screws, attached the tension spring, installed the storage drawer, and then slid the oven door back in place on the brackets, completing the repair.

The customer service rep was brilliant in finding the
right part number! It was sent the following day
(with email to let me know) The part itself was just
exactly like the old one. I simply turned off the power,
removed the 2 metal screws and unplugged the
broken element. The new one fit properly and works
like a million dollars. For about $50, you made me
look like a hero in my own house! Thjank you

Pull out oven and unplug from 220 outlet. Remove rear upper/lower cover (4 screws), Remove two wires from rear of element. From front, open oven door, remove two screws and pull out old element.
Install new element by reversing above sequence. Then test and push oven back in place. Easy!

removed oven door, removed drawer under oven, removed three screws holding hinge assembly, unhooked spring from hinge arm, inserted new hinge arm, attached spring, positioned hinge assembly and replaced screws, reinstalled drawer beneath oven being certain that no pot handles interfere with the hinge spring loaded arm, reinstall oven door.

Turn off power at the circuit breaker before working on electric thing.

Removed oven door and shelves for free access to element. Unscrewed the old element, pulled it out, removed the clips and removed the element. Reversed these steps to install the new element. Tested the element to ensure it worked.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires,held wires one at a time so tehy wouln't slip back into rear holes in oven, slid off connector tabs and pushed on to replacement unit...)

I unscrewed the two screws inside the oven, then i pulled the oven away from the wall and unscrewed the protective shield, and undid the wiring. Then i removed the element. Once the new one arrived, i pretty much just did the same thing in reverse. vwa-lah... fixed!

Slid off the oven door and loosened the hinge assembly. Removed the storage drawer to unhook the spring and then took off the old hinge assembly.

Inserted the spring into the new hinge assembly and then installed it - just tightened the screws. Hooked the spring into the lower point. Slid in the oven door and tested it so that is opened/closed easily. Cleaned under the oven while the storage drawer was out.

We can now bake bread, pizza, etc. What a relief.

Assumed this broken hinge was going to be an expensive service call. Decided to try and fix it myself. Ordered the part off partselect.com and got some repair tips off the website that made this a breeze. I am not handy at all but was able to complete the replacement in less than 30 minutes and spent only $30 on the part. Just needed to unscrew the old hinge and release the spring from under the stove (which I accessed by pulling out the drawer). It would have cost me over $100 to just get a service person to look at it.