79075750100 Kenmore Range - Instructions

It went easy, I ordered the part from another vendor, received it in 3 days and it only took about 20 minutes to install.
I do not recommend ordering from PartSelect!

First took apart oven door. then took out broken glass and replaced with new glass.Put everything back together done.

Very easy just had to pull the wire up that holds it secure.

First I removed the oven door from the range by removing 2 screws from the door. Next I removed 2 more screws from the oven door to get to the panel beneath. Once the top portion of the door was removed there were 4 nuts holding the glass sections together. Once these nuts were out I removed the broken class, replaced it with the new glass and reassembled. It was a very easy and quick project. I was so happy to find the part. I thought I was going to have to buy a new range. Thanks.

After looking over the installation instructions I was confident that I could perform this on my own, However, changing the burner orifices was a bit tricky. Getting the original ones out worked well, they stayed in the nut driver when it was lifted. One of the new ones fell out when inserting it. Thankfully it fell all the way down and I could retrieve it. A small piece of tape was needed to keep it in the driver. The rest of the install went per instructions.

See other posts.... they have the correct repair procedures.

HIGHLY RECOMMEND removing the bottom drawer to access the space where splice will be made between new igniter wires and existing wires. This step is recommended in previous posts. I wasted a lot of time taking out unnecessary stuff in the oven compartment before I realized that the drawer compartment provided easy access for repair. Story of my life on just about all repairs.

Remove bottom plates and deflector from oven, remove old igniter. Remove bottom drawer and panel to expose wiring. Cut wires, used supplied wire nuts to splice. The time consuming part of this job was having to clean all the parts before reassembly, and having to extract screws that were rusted into place due to heat and spillage. One of the igniter screws was stripped, and was very difficult to remove. The first part in your "probably cause" list was the right one! Thanks for the good service, and a useful website!

Was easy...I pulled oven out from the wall so I could get to the back.i used a nut driver to remove small silver cover.matched up wires to the never module and re installed.pluged oven back in and burners lit perfectly

Disconnected power cord to range
Removed the cover over the flame guard
Removed the Flame guard
Pulled out broiler drawer
Unscrewed the cover and disconnected the white plastic connector to the ignitor wires
Un crewed the two small screws to the ignitor and removed the old ignitor
Cut the two wires from the old ignitor
Connected the new ignitor to the wires on the white connector
Installed the new ignitor
Reassembled parts dsassembled
Plugged in power cord

Works

Got a copy of the parts breakdown for the oven door from partselect. Com. Removed 8 screws from outer frame (3 top, 3 bottom, 1 on eah side). Removed the main glass pane from oven door, be careful when doing this as this is most of the weight of the door. It will want close on its own due to lack of weight. Removed the 2 top screws that attach the handle. Removed some screws from some plates that retain the 2 panes of glass of glass. Removed the third (most inner, broken) pane of glass. Replaced with new one. Reversed disassebly procedure for assembly.

There were only 2 screws that held the door handle & cap in place, removed screws & handle to get cap pieces off. Ordered new cap, - lost screws - cap delivered - no screws had to order screws, damn! They're expensive too !! Got screws, installed handle & cap, now wife is happy again!

Very simple. Removed oven rack that had melted residue on it and replaced it with the new one from your company. I want to tell you that the delivery service I received was just geat. Took less than 48 hours to arrive at my home from the time I placed the order on line. Keep up the good work and I will be happy to share my experience with those in need of you services. Thanks. Marilyn Kasson

Replaced the ingintion module, still did not work, replaced the burner complete with new ingiter , it now works but another one quit . the front right one has 5 ohms resistance ,replaced with new one with 0 ohms, the back left has 2 ohms resistance and now it does not work , will need to replace that burner allso. too bad you can't buy just the spark module for the burner.

Having already removed the old igniter , replaced it with new.

1- put in new thermostat 2- put in new gas valve 3- put in oven igniter ....3rd time a charm. Now I have all new oven parts! My husband installed and said it was pretty easy, have to take the oven door off and inside bottom out.