66575822002 Kenmore Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Larry from Corona, CA
- Parts Used:
- 814229
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Nylon roller on bottom oven shelf broken off
The nylon roller was very easy to install. Although rather pricey for what the part was, it was shipped immediately and got the job done. Took all of 5 minutes to do. I wish all my repair jobs were that easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Deborah from MILWAUKEE, WI
- Parts Used:
- 814229
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Storage drawer would not completely open.
Replaced damaged drawer roller: easy peasy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kathryn from JACKSON, NJ
- Parts Used:
- 8190618
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven not heating up
Unscrewed the old part and replaced it with the new part.
My son repaired it for me.
My son repaired it for me.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from WALDORF, MD
- Parts Used:
- WP8053807
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Clothes would not fully dry in automatic cycle
1st gen whirlpool Duet dryer sensor not working in automatic cycle.
After ordering the moisture sensor harness which is about 6-8 inches long, I removed the lower panel and it is right there. I disconnected the two wire connectors in the upper left and I need a small screwdriver to disconnect the two pin connector which was a bit of a pain but once replaced I no longer had to use the timed setting to dry clothes and this will save me electricity.
After ordering the moisture sensor harness which is about 6-8 inches long, I removed the lower panel and it is right there. I disconnected the two wire connectors in the upper left and I need a small screwdriver to disconnect the two pin connector which was a bit of a pain but once replaced I no longer had to use the timed setting to dry clothes and this will save me electricity.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frank from LEBANON, VA
- Parts Used:
- W11594027
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
Light would not light
Pop old one out and new one in
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Glen from LOS GATOS, CA
- Parts Used:
- WPW10293048
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Wrench set
The Bake and Broil both stopped working. You could hear the igniters but no gas flowed.
Replace the gas valve. It is simple to replace, but please note that it comes configured for Natural Gas. If you are using Propane, there are two changes you need to make first.
1. Remove and invert the gas pressure regulator. See page 11 of the owners manual.
2. Tighten down the orifice hood all the way about 2 1/2 turns. It comes configured to stick farther up into the air mixer. See page 12.
1. Remove and invert the gas pressure regulator. See page 11 of the owners manual.
2. Tighten down the orifice hood all the way about 2 1/2 turns. It comes configured to stick farther up into the air mixer. See page 12.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from LARAMIE, WY
- Parts Used:
- 814381
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The side trim on the glass door needed to be replaced.
After we put the latch pins in, the door was easily lifted off. We placed the door on the table and unscrewed the trim pieces. The new trim pieces went into place after we cleaned the door. We slipped the door back on the oven and removed the hinge pins.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenneth A. from SANGER, CA
- Parts Used:
- WP3195097
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Pan scratched by housekeeper
Unscrewed old pan and screwed on new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Gaylord, MI
- Parts Used:
- W11594027
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
oven light not working
replaced light socket but did not repair problem. must have burned the motherboard.
pleased with service from your company.
pleased with service from your company.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Howard from Boynton Beach, FL
- Parts Used:
- 350930
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Both outside door handles turned very beige
Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Priscilla J from North Falmouth, MA
- Parts Used:
- W11213958
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
Install New Cooktop
We needed a repair man to do the job because we did not have the tool to remove the screws on the burner heads. Also the on line diagram was not accurate. It actually was much simpler than showed in the diagram. Had we done the job, we would have done a lot of dismantling. The repair man removed the old top in a flash and the whole job took about 40 minutes. He knew what he was doing. Detailed instructions should come with the part so the do-it-yourselfer could figure out how to do the job.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frances from palm beach gardens, FL
- Parts Used:
- WP179051
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
range handle fell off and screw got lost
It was worth the money for that little screw, since I didn't have to run all over trying to find the right one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dan from Caddo Mills, TX
- Parts Used:
- W11594027
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Inside Light would not work
Turned off CB for the oven,Remove the oven from the cabinet , remove the back of the oven, replaced the light Assembly. turned on CB for the oven, tested the light. and truned off the CB and replace the back and reinstalled the oven in the cabinet.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kristine from Drexel Hill, PA
- Parts Used:
- WP8053834
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
I shattered the original one when I took it out to clean it.
I placed the new glass in place, and replaced the screws. What I really want to tell abut is how QUICKLY my replacement part came from your company. I was so upset when I broke the original glass, but the replacement glass arrived within 24 hours! It was wonderful! Thank you!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph W from Anaheim, CA
- Parts Used:
- WPW10447925
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Burner Grate coating was damaged
Remove old grate and replace with new one.
Was this instruction helpful to you?
Thank you for voting!