9119114190 Kenmore Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Greg from Hamburg, IA
- Parts Used:
- WB44K5012
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Element turned into a welder
pulled out oven, unplugged power. Removed back cover for element, disconnect old element. Moved to front of oven and removed the two screws that held the old element,removed old element. Installed new element, connect element, installed cover, reconnect power.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- GARY from OREM, UT
- Parts Used:
- WB44K5012
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Bottom element would not heat
Remove two screws holding element. Pull element forward exposing connections. Pull connections apart. Replace with new element. replace screws. Done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from Burnsville, NC
- Parts Used:
- WB44K5012
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
oven would not heat on bake
The hardest part of repair was moving the oven from the cabnets to unplug and gain access to rear of oven. Remove rear cover panel unplug two spade connectors attached to the heating element. Open oven door and remove the two screws holding the heating element to back of oven. Pull heating element out. Then slide the new element in and assemble in reverse order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from Powder Springs, GA
- Parts Used:
- WB44K5012
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
Lower oven element burned out.
First I removed the two screws holding the element to the back of the oven. When I pulled the element out I disconnected the two wires and removed the element. I found the serial / part number on the existing part and order from PartSelect. The element arrived two days sooner than expected!! Replacing the element was a bit more difficult in that I had to pull the stove away from the wall and remove the rear cover in order to pull the wires and element through the insulation in the back of the oven. Four screws held the rear cover, but once those were removed the element easily went into place and the repair was finished. Cleaning behind and under the stove took a few extra minutes but the entire repair only took about 30 minutes, plus the wait time for the part. Two tips, pliers were used to disconnect and reconnect the slip-on connectors. The connectors were pretty tight and reaching to the rear of the oven was difficult to get leverage to pull apart and reconnect. Also, the oven light caused considerable glare on my glasses so I taped the door button controlling the oven light and used a flashlight to see inside. Otherwise, a simple repair. PartSelect had the best price on the element and service and delivery were excellent!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from Trenton, TX
- Parts Used:
- WB44K5012
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
Existing Element Broke
removed two bolts on the inside of the oven, disconnected the two electrical connections in back which were a little set so I had to use pliers and removed old element. Reversed procedure to install new element.
The >15 minutes includes vacuuming out the oven.
partselect.com deliver was extremely fast and the part was packed securely. We would order from them again without a problem.
The >15 minutes includes vacuuming out the oven.
partselect.com deliver was extremely fast and the part was packed securely. We would order from them again without a problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ladd from Danville, IL
- Parts Used:
- WB44K5012
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
baking element burned out
pulled stove out from wall about a foot ans disconnected the electricity cord. removed the 2 screws holding the element in place and pulled it out a bout 3 inches and disconnected the two wires. attached the new element & pushed it in place and tighrened the 2 screws. hooked up the electric power, moved stove back in place & it was done!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joan from Mascotte, FL
- Parts Used:
- WB44K5012
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Old Element Was Rusted.
Very well, I made a mistake with the model #. So I had to return and reorder .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- eric from Melbourne, FL
- Parts Used:
- WB44K5012
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Bake element burned out
With less than 24 hrs from ordering to delivery, I was making cookies. Installation was quick and painless.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- brad from flatwoods, KY
- Parts Used:
- WB44K5012
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Heating element broke and not working
Watched youtube....
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Dumfries, VA
- Parts Used:
- WB44K5012
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Oven bake element burned out (literally!)
Removed oven door & shelves. Removed the 2 mounting screws & compared parts to verify I ordered the right one, then plugged it right in! Managed to drop & lose one of the screws while re-installing them. Got a stainless sheet metal screw from the hardware store that fits, but will probably order an exact replacement because the size & thread are slightly different. All in all, other than losing the screw, it was a quick, easy task.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Shane from Roy, UT
- Parts Used:
- WB44K5012
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Bake element was broken
Remove the oven racks, remove the two retaining screws, unplugged the wires. Install wires on new bake element, insert element into opening, install & tighten retaining screws, replace oven rack's & there you have it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cynthia from Okeana, OH
- Parts Used:
- WB44K5012
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bake element set itself on fire and burned in half
First - really check that the part you order will fit. Our oven is 30 years old and the first part we ordered was not correct, but it came the very next day after we ordered it which is amazing. We were more careful about measuring for the second one and it came almost as quickly. It only took a few seconds to unscrew the old element and then reattach the wires to the new one and screw it back into the oven. Very simple. I highly recommend PartSelect.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Amy from Etna, CA
- Parts Used:
- WB44K5012
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench set
bake element in oven burned out
Using a wrench, removed old element and simply installed new one - took less than 10 minutes and the oven was working again! Best part was how quickly the item reached us - ordered it on a Wednesday afternoon and had it by Friday afternoon, with no expedited shipping - Great Service!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- joseph from mastic, NY
- Parts Used:
- WB44K5012
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Bake element burns out heating up easter dinner
Uplugged the oven and undid the back contact cover, removed the nuts inside the oven and slid out the element. Pushed the new element into place and secured it. Attached the contacts and replaced the cover. Plugged it in and got cookin'.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Murray from Franklin Square, NY
- Parts Used:
- WB44K5012
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
bake element burned out, lower unit
removed nuts from inside, removed rear panel, pulled old
part out, slipped new part in.
DONE
SHIPPING AHEAD OF TIME, YOUR COMPANY SAVED ME THE PURCHASE
OF A NEW STOVE. THANK YOU FOR FAST & GOOD SERVICE.
NO ONE HAD THE PART BUT YOU FOLKS.
part out, slipped new part in.
DONE
SHIPPING AHEAD OF TIME, YOUR COMPANY SAVED ME THE PURCHASE
OF A NEW STOVE. THANK YOU FOR FAST & GOOD SERVICE.
NO ONE HAD THE PART BUT YOU FOLKS.
Was this instruction helpful to you?
Thank you for voting!