9114698812 Kenmore Range - Instructions

Following the repair video made the job very easy and quick, about a 5 minute repair. Wife says oven door never worked better. Thanks a lot for all your help.

It took longer to watch the video on how to replace the hinges than it did to replace them. Simple and easy. Video knocked it out of the park for ease. And now the oven door works great! thanks!!!! Video suggested if you're replacing one side do both, couldn't agree more.

There was missing door catch in the lower door of the kermore range so I installed the new one into the existing catch bracket so the lower door is able to close firmly.

This repair was super easy. I removed the two screws holding the oven sensor in place, pulled the sensor from the oven wall to expose the two wires attached to the sensor cut and spliced in the new sensor as per instructions. The supplied wiring kit made this splice very easy. I then reinserted the wires and sensor from the oven wall, put the screws back in place tested the oven. Oven now works like new and I got bonus points from a happy wife!

1. Google your appliance problem. 2. Watch whatever YouTube videos that are available. 3. Follow the excellent instruction provided by PartSelect.

replaced both hinges in no time flat and it was easy to find the part and instructions on parts select. Thank you

changed burner and replace light receptical. easy job great service from supplier.

I did as the video suggested.....I cut the old wires and spliced new ones already attached to the new terminal block. It would have been nice to have some instructions with the parts as I expected one piece but had to connect the wires to the new block and the new metal cover. I was guessing a bit. Also, I needed to use the holder strip off my old part so that it displaced the new part back far enough to insert the burner connections. That meant finding a screw and nut small enough to allow the metal cover to fit on the block. But the burner works great. I've learned that any repair requires some ingenuity.

We are really excited to have this burner working again. We originally paid a repairman to come out and he said that he couldn't get parts so we would just have to live with it or replace the whole cooktop. We received the new burner within a few days of ordering. I pulled the two burner unit out of the cooktop, easily removed about 7 nuts and had access to the burners. It was a perfect replacement and fit right in. The only place I had to spend a little extra time was where the connection wires are screwed to the burner. One unscrewed but the other one broke and I had to cut it off the old unit and remove a little wire insulation before re-installing.

Followed YouTube video from PartsSelect. It was real easy to do and that video was helpful. Took off door by sliding it up off hinges, disconnected springs, unscrewed hinges & slid them out - reversed to install. Worked perfect, parts were exactly right and parts came within 2 days.

Very,very easy. Just like the video described. Removed three screws. Released the spring and removed the old hinge from the slot. Slipped the new hinge in the slot,replaced the screws and reattached the spring. Job done! Great service!

When I got the part I removed the tin cover (two screws)on the back of the range. I removed the sensor by removing the two screws inside the oven and pulled out the sensor. taking the instructions advise, I checked the sensor with my ohm meter and although it read 1.1 ohms as compared with the recommended 1.09 ohms at room temperature in the instructions, went ahead and changed the unit. The connector did not fit my particular model so I spliced the wiring and using the two included wire nuts made the connection. I reinstalled the sensor, reattached the gas line, plugged it in and tried the oven before I put it back in place. The oven works great now and it was super easy.

the original path was from the right front control knob around the back of the range and left side of range,which i dismantaled to install the new wires to the right front burner. When I found them to be to short I had to also dismantal the right side so the wires could be routed there. The new wires worked fine but did take some extra time.